Posted on Leave a comment

“Wrinkly Pig” Corset Case Study

This entry is a summary of the review video “Wrinkly Pig” Corset Case Study”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

***

Note: the following are the differences between the “Wrinkly Pig” and the “Tickled Pink” corset in terms of construction:

  Wrinkly Pig Tickled Pink
Fusing Fused the brocade to a layer of woven fusible interfacing, then flatlined that to coutil. Fused the brocade directly to a layer of coutil using “Heat n’ Bond” (fiddly sheet of glue, I don’t recommend it).
Roll-pinning Everything was flat-pinned, not roll-pinned. Some roll-pinning was done on the side panels.
Seams Lock-stitched seams; allowances were not trimmed or clipped at curves. Seams were trimmed and flat-felled.
Boning channels Double-boned at the seams, sandwiched between two layers of coutil. Single boned at the seams, used external boning channels (cuts down on wrinkles slightly)

***

And here is my review:

Fit, length Decent curves. Used to be a slightly long-line corset but I later shortened the hips so it is more of a cincher now. Center front is about 11″ long.
Material 4 layers including the interfacing: brocade fashion fabric fused to interfacing, then flatlined to interlining of coutil and another lining of coutil.
Construction 6-panel pattern. Seams were lock-stitched (stitched twice) at the seams, the allowances were pressed open. The brocade/interfacing/coutil flatlined panels were all assembled, then the coutil lining was assembled. The layers were then stitched together at first/last panels, flipped right-side out and stitched in the ditch between panels and also secured at boning channels.  Bones are sandwiched between the two layers of coutil.
Binding The binding at top and bottom are made out of commercial hot pink cotton bias tape, machine stitched on both sides.
Waist tape 1” wide twill tape between the coutil lining and interlining, stitched invisibly so it’s not noticeable.
Modesty panel Suspended modesty panel made from brocade fused to twill, and stiffened with plastic canvas. 7″ wide.
Busk A standard flexible busk, 1/2” wide on each side, with 5 pins, 9.5″ long.
Boning 22 steel bones in this corset not including the busk. The seams between the panels are double-boned (except the seam closest to the grommets with ¼” inch wide spirals, and there are a pair of flats sandwiching each column of grommets.
Grommets There are 30 2-part size #X00 eyelets (15 on each side). They have a medium flange around and are spaced out 3/4 inches apart. No pulling away of fabric yet but they are very small so many types of fat cord is hard to thread through.
Laces 1/2″ wide double-face satin ribbon, baby pink in colour. About 5 meters and not really long enough for my tastes. I think I may change out the laces for some longer ones.
Price If I were to re-make this corset, I would roll-pin the panels and also use wonder-under or stitch-witchery to directly fuse the brocade to a layer of coutil to eliminate wrinkling. Keeping other construction techniques the same, I would likely charge around $260 USD for a corset like this.
Posted on 1 Comment

CorsetDeal Silver/Black Gothic Overbust Review

This entry is a summary of the review video “CorsetDeal/Corsets-UK Gothic Overbust Review”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Gently curved, gives a slim silhouette without a lot of cinch. The center front is 14”. From the apex of the bust to the bottom is not quite 15″, and the longest part (the side, where the hips peak) is 15.5″. Good coverage in the bust.
Material Two layers; the outside has alternating panels of smocked shiny black PVC and flocked black and silver floral polyester brocade. The inside cotton twill.
Construction 6 panel pattern. Panels are top-stitched at the seams, with seam allowances always pressed toward the brocade side. Internal boning channels laid down made of black twill.
Binding The binding at top and bottom are black shiny PVC. Also has 6 garter tabs.
Waist tape Waist tape running through the corset, seen on the inside, made of 1” wide single-faced satin ribbon.
Modesty panel Unboned modesty panel, 7.5 inches wide made from silver/black brocade on the outside and black twill on the underside. Also has a 3″ wide placket beneath the front closure, made from PVC on the outside and twill on the underside.
Swing Hooks 5 large silver swing hooks riveted to half-inch-wide bones in the center front. The bones in front are 12.5″ long. Very strong, no sign of breaking or falling out. I like that there were 5 swing hooks used – the extra hook a the waist prevents bowing of the bones in this area.
Boning 14 steel bones in this corset not including the busk. Single boned on the seams. The two bones that curve over the bust are made of spiral steel; all the other bones in this corset are spring steel.
Grommets There are 24, 2-part size #0 grommets (12 on each side), finished in nickel. The grommets are sturdy with moderate size lip around, there is absolutely no fraying around the material, they’re not pulling out.
Laces Black flat nylon braided shoe-lace style. Very strong, grips fairly well. It has a little bit of spring. They are resistant to fraying and catching.
Price Currently around $164 USD or £105 GBP.

 

Final Thoughts:
This is such a fun corset. If I ever had tea at H.R. Giger’s house, this is probably what I would wear. It’s an interesting combination of elegance and edginess.
Of all the overbusts I’ve reviewed made by CorsetDeal/Corsets-UK/Punk69, this is the one that fit me the best. It’s also the corset that I was most impressed with in regards to workmanship/stitching – I know from personal experience that PVC is not easy to work with! I might have kept it in my collection if I had any place or reason to wear it, but unfortunately it’s not a style I often wear, and I don’t go out that often. This corset would be great for clubbing/performances, and for attracting some attention when going out on the town.

For those interested in trying a corset from CorsetDeal, I’ve found a coupon for 20% off anything on the CorsetDeal site here (aff link).

Posted on 53 Comments

Isabella Corsetry “Josephine” Underbust Review

This entry is a summary of the review video “Isabella Corsetry Josephine Underbust Review”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Dramatic curves, extreme hourglass. This is a longline corset coming over my hips. The center front is 13” high; the shortest part of the corset is 10.5″ hiugh.
Material 3 main layers. The outer fashion fabric is black satin, then there’s a layer of twill as interlining and another layer of black twill as lining.
Construction Made from a 6-panel pattern (so the corset itself is 12 panels total). It looks as though the coutil panels were lock-stitched at the seams, the allowances were pressed open. The layers are joined together by stitching in the ditch between the panels and also by making boning channels. The stitching is perfect on the outside, but the seams are wiggly on the inside. The lining does not float. Bones are sandwiched between the two layers of twill (lining and interlining).
Binding The binding at top and bottom made out of black satin bias tape machine stitched on both sides; it’s small on the outside, then folded under and machine stitched in the ditch, in the seam between the corset and the binding itself, to catch the rest of the binding underneath.
Waist tape 1” wide twill tape between the lining and interlining, invisibly stitched.
Modesty panel There an unboned modesty panel in the back made from two layers of just satin. Slightly over 6” wide.  Easily removable if you want to remove it. No modesty placket on the front.
Busk A heavy duty busk, slightly under 1” wide on each side and 11” long, with 5 pins, it’s EXTREMELY stiff. Keeps the front very straight.
Boning 22 steel bones in this corset not including the busk. On each side there are 9 spirals about 3/8” wide, and they’re mostly double boned at the seams except for at the back between panels 5-6. By the grommets they also use about 3/8” wide flat steels; very sturdy.
Grommets There are 30 2-part size #00 grommets (15 on each side). Black finish to match the rest of the corset, they have a medium lip around and are spaced equidistantly. Functionally they’re very sturdy, no popping or pulling away, whatsoever. On the underside there are no splits – much nicer than the grommets used in Isabella’s Bat cincher.
Laces 1/2” wide black double satin ribbon. They’re very nice, strong, pretty, glide through the grommets nicely and also seem to hold the bow well with little slipping out over time.
Price Currently $175 USD for immediate line. For other fabrics (made-to-order) it’s $250, and for custom fit/fabric it’s $360.

Final Thoughts:
This corset continues to be one of my favourite off-the-rack underbust corsets. It’s comfortable and gives a crazy curvy silhouette – to this day, I think I have gotten more compliments when wearing this corset than with any other off-the-rack corset. It’s relatively affordable compared to other major brands out there. The only con I could say is that Isabella is quickly gaining more and more recognition and thus she’s becoming busier, so wait times have been increasing for her corsets! However, I’m happy that she’s overflowing with commissions; I think her work should be credited. I could definitely see myself commissioning another piece from Isabella in the future.

Posted on 19 Comments

Heavenly Corsets Wasp-Waist Training Underbust Review

This entry is a summary of the review video “Heavenly Corsets “Wasp-Waist” Training Underbust Review”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

***

Note: the following are the differences between the “standard” wasp-waist corset and the “training” wasp-waist corset:

  Training Corset Standard Corset
Materials Always made in coutil, with an inner layer of twill, and a cotton lining layer Either a layer of outer fabric (unless coutil) with an inner layer of twill and cotton lining layer OR if you chose coutil, a single layer of coutil and a cotton lining layer
Boning double boning throughout 6 fewer bones than the trainer
Busk wide solid steel busk standard steel busk
Modesty Panel included NOT included
Seams triple-stitched seams double-stitched seams

***

And here is my review:

Fit, length Dramatic curves, “wasp-waisted”. This is a longline corset coming over my hips. The center front is 12” high. Measurements (both circumference and vertical) were taken to fit my body; quite comfortable with no pinching. One issue with the bones in the back bowing outwards and twisting so creates a gap at the waistline.
Material 3 main layers. The outer fashion fabric is red satin coutil, twill interlining and lightweight cotton lining inside.
Construction 6-panel pattern. It looks as though the coutil panels were lock-stitched (stitched twice) at the seams, the allowances were pressed open and zigzag stitched again. (Some people may not find this aesthetic but if it makes for a strong corset then I don’t mind.) Bones are sandwiched between the satin coutil and the twill, and the cotton lining is primarily floating.
Binding The binding at top and bottom are made out of commercial red satin bias tape machine stitched on both sides; it’s folded under and stitched in the front and then topstitched to catch the back.
Waist tape 1” wide twill tape between the lining and the twill interlining. Stitched down horizontally across all the panels of the lining (so is not invisible but still cannot be felt).
Modesty panel Unboned modesty panel, 4.5 inches wide made from satin coul on the outside and lightweight cotton on the underside. No placket beneath the busk. (I would have preferred a slightly wider panel.)
Busk A heavy duty busk, 1” wide on each side, with 5 pins, it’s quite stiff and it’s 11” long.
Boning 22 steel bones in this corset not including the center front, ALL flat bones. The seams between the panels are double-boned (except the seam closest to the busk) with 3/8 inch wide flats (slightly wider than ¼”), but on the outer edge of the grommets in the back those bones are ½” wide flats.
Grommets There are 20 2-part size #00 eyelets (10 on each side). They have a medium flange around and are spaced out 1¼ inches apart. I would prefer for them to be spaced closer together and there be more of them, but functionally they’re sound; no pulling away or fraying of the fabric. On the underside there are no splits.
Laces  ¼” wide flat braided cotton laces, NOT nylon. They’re easy to pull and they grip well, not much wear so far. Cotton laces are sometimes prone to snapping so should be replaced more often, however I’ve had this corset for about 9 months and haven’t had to change the laces yet.
Price Currently £160 ($250) for the 23/7 waist training wasp-waist corset, or £120 ($185) for the non-training wasp-waist corset.

Final Thoughts:

I received a mixed reaction from this review. A few previous customers of Elle came forward and told me that they didn’t like certain aspects about this style of corset, such as a wobbly stitch line here or there, or the fact that she uses all spring steel bones. I put all this into perspective. Back in 2012, I hadn’t found a more affordable 23/7 training piece, and the materials used (including English coutil) are quite high quality. From what I can see, the primary stitch lines (the straight ones, holding the panels together) are straight and even, and although the zig-zag stitching (which is technically the 3rd stitch on each panel) does veer a bit and is not aesthetically pleasring, it still serves its purpose – to further reinforce the panels together. At that point in the construction process, it has no effect on the overall shape or measurement of the corset.

This did not come as a surprise to me, because I asked Elle a thousand questions before I ordered (and she was quite patient with me every time). The purpose of this corset (for me) wasn’t meant to be pretty or be shown off on a regular basis, it was meant to be strong.

Edit December 2014:

It’s been about 4 years since I ordered this corset, and nearly 3 years since the review – truthfully, I had forgotten about this corset review until recent events brought it back to my attention.
How did my corset hold up? The seams remained strong and none of the bones wore through their channels, but the very flexible bones in the back by the grommets became annoying, so I ended up switching them out for stronger (but more narrow) 5.5mm steels from Vena Cava. I also added more grommets between the pre-existing ones in the back of the corset for better control (the size #00 self-piercing grommets that fit the C-Step 2 machine are a decent match), and changed the lacing style. This was the only issue I experienced with my corset. However, other clients of Elle have had different experiences than myself, and I encourage you to read some of the comments below so you can gain a balanced view before deciding.

Posted on Leave a comment

Grey & Green Longline Underbust Case Study

This entry is a summary of the review video “Grey & Green underbust case study”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Self-drafted, longline (low over the hips) underbust corset with a peaked front top and a straight bottom edge. Made to close at 22″ at the waist. I took 5 horizontal measurements and 9 vertical measurements to draft this.
Material Fashion fabric is a black/white fine herringbone weave with metallic gold thread pinstripes This was fused to herringbone coutil interlining and lined in fern green satin.
Construction Drafted from a 6-panel pattern and both topstitched and lockstitched for extra strength. Boning channels are external (made from green satin fused to coutil) and the lining floats.
Binding The binding at top and bottom are made from 2-inch-wide strips of green satin, machine stitched on both sides.
Waist tape 1-inch wide waist tape, invisibly stitched between the coutil and the lining.
Modesty panel Suspended modesty panel stiffened with plastic canvas and finished the same way as the corset – covered in the pinstripe fabric and bound with green satin on top and bottom.
Busk Heavy duty stainless steel busk (1″ wide on each side) and was cut to 13″ long, with 5 pins.
Boning 20 bones not including the busk; I had used 1/4″ wide spirals double-boned at each seam (except the one adjacent to the busk) in the external channels. By the grommets there’s a 1/2″ wide flat bone on the outer edges and 1/4″ wide flat bone on the inner side.
Grommets There are 32, 2-part size #0 grommets (16 on each side), finished in silver (Chelsea’s choice). The grommets have a large lip around and are spaced 3/4″ inch apart down the length.
Laces Flat nylon braided shoelace-style laces; 8 yards long. They grip well, are densely woven and are resistant to catching, fraying or snapping.
Price The retail price for something similar is around $280 (underbust corset + heavy busk upgrade + double boning upgrade + external boning channels upgrade).
Posted on 7 Comments

Isabella Corsetry “Bat Cincher” Review

This entry is a summary of the review video “Isabella Corsetry Bat Cincher Review”. If you would like more complete information, detailed close-ups and side notes about the corset, you can watch the video on YouTube here:

Fit, length Dramatic curves, I would say “wasp-waisted”. This corset starts lower down on the ribcage on me so I have room to move and to breathe, yet this is a longline corset coming over my hips. The center front is 11.5” high.
Material 3 main layers. The fashion fabric is a custom-printed cotton which is interfaced. There’s a twill interlining and another layer of black twill for the lining.
Construction 4 panel pattern. This constructed in what seems to be the sandwich method; each layer was assembled individually and then the layers were stitched, wrong sides together, at the seam of each panel. Bones are inserted between the two layers of twill (being the lining and interlining).
Binding The binding at top and bottom are made of lime green satin bias tape. Each curve between the peaks of the “bat” shape are individually bound. It’s stitched neatly on the outside, and then just folded down and machine stitched again in the “ditch” of the first stitching.
Waist tape 1-inch-wide waist tape running through the corset between the layers (inserted invisibly).
Modesty panel None.
Busk A heavy duty busk with 5 pins, it’s quite stiff and 1” wide on each side. 11″ long.
Boning 16 steel bones not including the busk. The seams between the panels are all double-boned with ¼ inch wide spirals, and then 3/16 inch wide sturdy flats on each side of the grommets.
Grommets There are 26, 2-part size #00 grommets (13 on each side). I’m very impressed at how well the grommets have held up. None of them show any sign of pulling out whatsoever, despite the fact that every one is split along the back.
Laces Came with ½” wide ivory double-faced satin ribbon which has held up remarkably well.
Price Bat cincher available as “made to order” for $225. If you want custom fit, the closest other corset is the “Vamp” at $350.

Final Thoughts:
This corset is cute as a button. I adore the crazy fabric print (although that is to be credited to the original person who commissioned this corset) and the cut of this corset is crazy curvy. I’m still impressed by how curvy Isabella managed to make this with just four panels per side. I did have issues with this corset, like a wobbly binding seam here or there, and the split, small grommets, and admittedly the flesh over my ribcage did give a “muffin top” over the top edge (that may have been because it was made to another girl’s measurements and not mine) – however, when comparing this corset to the Josephine, there is a great difference! I know that the Bat cincher is a couple of years older than my Josephine corset, so I have the unique opportunity to see how the workmanship of a corsetiere has changed and improved in a short time. This is why I don’t want to say “never” in terms of ordering twice from a (fairly reputable) company. If I have reason to believe that their work has improved, I will sometimes give them the benefit of the doubt even when my previous experience wassn’t 100% positive or as expected.

Posted on 2 Comments

Homemade Corset: Grey Longline Closed-Front Underbust

This entry is a summary of the review video “Showing my homemade corset”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Drafted from Foundations Revealed pattern tutorial. It’s a longline underbust corset with a center front of about 13″ and a waist of about 23″, with an extreme hourglass silhouette. I made the ribcage a little too large so the back seams look like / instead of ||
Material Made out of a black/white fine herringbone weave (I call it grey because that’s how it looks from afar) with gold metallic thread as an outer layer, and one layer of down-proof cotton ticking as a strength layer, which generally doesn’t stretch, but isn’t as strong as coutil.
Construction Drafted from a 5-panel pattern and constructed in the “sandwich” technique in which each layer has its panels individually assembled and then the two layers are attached at the ends, flipped right-side out and then bones are sandwiched between the layers.
Binding The binding at top and bottom are made out of bias strips of the same white/black herringbone fabric.
Waist tape 1-inch wide waist tape, invisibly stitched between the two layers. It’s slightly tighter than the panels of the corset which is what causes the “groove” around the waistline of the corset.
Modesty panel None.
Busk None, this was before I knew where to buy busks (other than the overpriced ones at anime conventions) so I made this with a closed front
Boning 22 bones including the bones at the center front; I had used 1/2″ wide hoop steel for the center front and by the grommets, and 1/4″ wide flats double-boned at each seam. These particular flats were flimsy, which is how I got the silhouette without resistance to the bones.
Grommets There are 24, 2-part size #X00 grommets (12 on each side), finished in gold (the only colour I could find at the time). The grommets have a small size lip around. One of the grommets later popped out at the waistline.
Laces Flat cotton braided shoelace-style laces bought at Timeless Trends; 7 yards long. They grip well, have no spring and are very easy to tighten, however they do snap after about a year of regular use.
Price Cost me probably around $40-$50 in materials, and around 24 hours total to make – this was my 3rd corset so I was still moving very slowly through the steps.
Posted on 5 Comments

CorsetDeal Longline Pinstripe Overbust Review

This entry is a summary of the review video “Longline Overbust Review (CorsetDeal/Corsets-UK)”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Gently curved, gives a slim silhouette without a lot of cinch. The center front is 15.5”. The longest part of the corset at the apex of the bust is 18”. Sweetheart neckline. Longline corset, ending low over the hips.
Material Two layers; the outside heavy polyester pinstripe fabric, and the inside cotton twill.
Construction 6 panel pattern. Panels are top-stitched at the seams, and then internal boning channels laid down, made of black twill.
Binding The binding at top and bottom are black polyester bias tape. Also has 6 garter tabs
Waist tape Waist tape running through the corset, seen on the inside, made of 1” wide single-faced satin ribbon.
Modesty panel Unboned modesty panel, 8 inches wide made from polyester pinstripe on the outside and black twill on the underside. No placket beneath the busk.
Busk Slightly heavy duty, almost 1″ on each side. Stiffer than a standard flexible busk. 14″ long with 6 pins.
Boning 14 steel bones in this corset not including the busk. Single boned on the seams. The two bones that curve over the bust are made of spiral steel; all the other bones in this corset are spring steel.
Grommets There are 32, 2-part size #0 grommets (16 on each side), finished in nickel. The grommets are sturdy with moderate size lip around, there is absolutely no fraying around the material, they’re not pulling out.
Laces Black flat nylon braided shoe-lace style. Very strong, grips fairly well. It has a little bit of spring. They are resistant to fraying and catching.
Price Currently ranges from $40 USD – 85 USD (£25 to £54 in UK).

 

Final Thoughts:

After experiencing the unflattering way the shorter Corsetdeal overbusts barely covered my girls, I opted for a longline style instead. This was a slightly better fit. I definitely felt that my bust was more secure, and the position of the waist tape was in a more reasonable place, although still not right at my waistline (it was sitting perhaps an inch above my natural waist).

The pattern for the overbust corsets have the same bust/waist/hip circumference as the pattern for the regular overbusts, so keep this in mind. It’s as if they took the original pattern and simply stretched it out vertically to elongate it (i.e. what they did not do, was theoretically take the original pattern and extrapolate the lines to longer [and wider] top and bottom edges). I hope at explanation made sense – if not I will draw a diagram for you all. How this translated to fit on me, is that it fixed the flaring issues that I had at the hips in my shorter overbust corsets, but it resulted in the appearance of a less curvy corset overall. Therefore I recommend this corset to buyers who are tall/ have a long torso, and are either slim/ruler shaped, or slightly apple shaped. If you are a pear or natural hourglass shape, there is a possibility that this corset may not be curvy enough for you.

I didn’t have any problems on my hipbones here in terms of the pattern itself, although the placement of the internal bones at the side seams was unfortunate, as the rigid spring steel bones sat right over a nerve on my iliac crest, causing some chafing and discomfort. The problem was partially resolved by simply replacing the flat bones on the sides with more flexible spiral steel boning, which was a surprisingly easy operation.

For those interested in trying a corset from CorsetDeal, I’ve found a coupon for 20% off anything on the CorsetDeal site here (aff link).

Posted on Leave a comment

Axfords C242 Lace Underbust Corset Review

This entry is a summary of the review video “Axfords C242 Corset Review” which you can watch on YouTube here:

Fit, length Circumferential measurements are very comfortable; no pinching in the hips or ribcage. Much curvier than I was expecting. This is a longline corset, starting lower on the ribcage and ending low on the hips – center front is 11″.
Material 3 layers: the strength layer is the inside lining – a tightly-weaved white cotton coutil (made especially for Axfords). Coral satin fashion fabric is flatlined to the coutil, and then the white real lace is laid ontop of the satin.
Construction The seams are top-stitched; bones are in internal boning channels at the seams made from twill or Prussian tape.
Binding Satin on one side and grosgrain ribbon on the other side. Quite unique from commercial bias binding used in other corsets. Neatly machine stitched on both sides.
Waist tape None.
Modesty panel Attached 6″ wide protector, not boned but it is stiffened, so it’s flexible but stands on its own. When I’m lacing down it doesn’t need to be adjusted, and it curves nicely with the contours of my spine. Very comfortable. Has a placket overtop of the busk to hide the hardwear.
Busk Heavy busk, 10″ long and one inch wide on each side. Quite a bit stiffer than the standard flexible busk.
Boning 14 bones total. There are 10 hefty spiral bones – they’re 7mm wide instead of 5mm wide. Also four ¼ inch wide spring steel bones which are also very sturdy and quite thick.
Grommets 30 grommets total, size #00 two-part grommets with moderate flange; set equidistantly. Axfords says that they use smaller grommets set closer together for more controlled tightening of the corset. Some splits along the back of the grommets but they do not catch on the laces and are not pulling out.
Laces Strong tightly woven braided shoe-lace style laces; they’re thin, they grip well and they are very long. No stretch or spring to the lace.
Price Currently £125 ($195 USD) for the lace overlay style, but £115 ($180 USD) without the lace.

Final Thoughts:

This corset is adorable, feminine, pretty, shapely… I think this is the girliest underbust I own – pink with floral lace. I’m impressed at how smoothly the delicate lace lays (say that five times fast!) over the pink satin – do I detect some roll-pinning? ;) Even when worn at large reductions, the lace does not pull away from the seams or wrinkle up with stress.

I was initially concerned about the strength fabric as it was said to be coutil but didn’t have a herringbone weave – this was my first experience with a plain-weave coutil – yet it has stood up the test of time, even without a waist tape. The grommets are also still holding up well several months later – I find my preferences now leaning towards more and smaller grommets on my lacing panel as it’s easier to make fine adjustments when lacing up.

The fit of this corset is flattering as well (in my opinion); I like the conical ribcage, and the hip gores make this longline corset very  comfortable over my hips. The shape is quite similar to the Mae Extreme corset by What Katie Did – I am able to cinch down further in this corset than I was able to in the regular Mae.

All of Axfords’ corsets come with a complimentary storage bag as well – of course, don’t buy a corset just for the bag, but only if you think the corset is as lovely as I think it is. You can see this corset in other colors, and other corset styles on their website here.