This entry is a summary of the video “Case Study: Homemade Mesh ‘Corset'”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:
|Fit, length||Center front is 11″ high, and I drafted this corset to be very curvy: underbust about 32″, closed waist 23″ and hips 34″. The elastic mesh also contributes to the extreme shape and curviness.|
|Material||Heavyweight powernet (quite stretchy) for most of the panels, and black satin coutil for the first and last panels, the boning channels and the diamond waist tape.|
|Construction||Essentially a 6-panel pattern although the last panel is separated into two to make 7 panels. First, the powernet panels were sewn together wrong sides together and flat-felled with the bulk being on the outside of the body. Then I added the center front coutil panels, with the diamond waist basted in front. The diamond extends into a waist tape, which was basted at each seam, then I secured the external channels down on top of it. The back coutil panel went on last, then I added the busk and bones, and lastly serged the top and bottom edges.|
|Binding||There is no binding on this *yet*. I had serged the raw edges to keep them from fraying. This allows the mesh to stretch. Conventional binding would not allow the top and bottom edges of the corset to stretch. However I may later add an elastic or mesh binding.|
|Waist tape||The diamond detail made from satin coutil extends into a waist tape that is slightly more than 1 inch wide, and placed on the external side of the corset, secured down at the boning channels.|
|Modesty panel||I didn’t make a modesty panel for this corset because I designed it to close completely at the back. There is a small modesty placket in the front by the busk.|
|Busk||A standard flexible busk, 1/2” wide on each side, with 5 pins, 9.5″ long. Although it is quite flexible, having 3 layers of satin coutil surrounding the busk makes the front panel quite sturdy.|
|Boning||20 bones total in this corset (not including the busk). On each side there are eight 1/4″ wide spirals in external channels, then a 1/2″ wide flat steel on the center back edge of the grommet panel, and a 1/4″ steel on the “inner” side of the grommets.|
|Grommets||There are 26 2-part size #00 grommets (13 on each side). I used self-piercing grommets to insert these, placing the grommets closer together than I normally would and making sure the grommets are snug between the two flat bones. So far they have all held up well.|
|Laces||Some old black cotton shoe-lace style. More lightweight than nylon laces but not as strong. I just used whatever I had lying around.|
|Price||This corset was quite time consuming due to the flat-felled seams and external channels and waistband. Also the powernet and satin coutil were both expensive materials. If I were to remake this corset (with a more pristine finish) it would likely start at no less than $280.|
This is an extremely comfy corset. I also feel that I’m able to very easily cinch down in this corset – I wish I had drafted it to be another inch or two smaller! The powernet is forgiving of curves and makes my asymmetric hips look symmetric, while giving me absolutely zero pinching or discomfort.
The only disappointments I had with this corset was a) the asymmetry in the diamond detail, and b) the rough finish of the serged edges. I may end up adding binding to this corset (either elastic or mesh) although that would somewhat ruin its ability to be worn inconspicuously under clothing, and I’m not sure how even elastic binding would bring back the dreaded muffin top which is currently so nicely avoided.
Overall I think this experiment turned out much nicer than I had anticipated, and I think I will use this as a sleeping corset in the future! However I do need to practice my “finishing” of corsets, even when they’re experiments or prototypes.