Posted on 2 Comments

Stormy Leather Lombard Overbust Corset Review

This entry is a summary of the review video “Stormy Leather Lombard Overbust Review” which you can watch on YouTube here:

Fit, length This corset is custom fit (made to measure), so a corset for you may fit differently. Center front is about 16 inches high, and there are adjustable shoulder straps so there is no real point where the bustline “peaks”. Measurements of the size Small: Waist 22″, underbust 26″, full bust 28″, high hip (iliac) 32″. Gentle hourglass, slightly 18th-century-inspired hybrid.
Material 1 layer of unlined leather. While this corset does pull me in, the website mentions to expect the regular leather to stretch a couple of inches over time with regular use. The center-front panel is treated (patent leather), so less stretchy than the other leather.
Construction 5 panel pattern, very flat front. For assembly, there is nothing to flatline as it’s a single layer. Panels were stitched together, with internal cotton boning channels straddling each side of the seams for extra strength, while at the same time covering the seam allowances. Single boned on seams.
Binding Matching strips of leather, machine stitched on outside and inside (stitched in the ditch). Inside has a raw edge (normal for leather binding) but edges were not folded over, rather just cut off at the corners.
Waist tape None.
Modesty panel Back modesty panel is 4.5 inches wide, continuously boned with six 1/2″ wide steel bones. Finished in leather, stitched to one side. Front placket is a single layer of patent leather.
Busk 14 inches long, standard width busk (half inch on each side) with 7 knobs and loops, equidistantly spaced.
Boning 10 bones total (5 bones per side). All 1/2″ wide flat steel bones, single boned on the seams, and in the back by the grommets there is only a single bone in the center back edge (not sandwiched on each side).
Grommets 26 two-part grommets, size #00, large flange, held in strongly, set equidistantly. Nice washers, grommet rolled on the back with no splits.
Laces The original laces were 1/8″ wide round nylon cord, too slippery and frustrating to use so I switched it out with some longer, gripper flat laces.
Price At the time I’m writing this, the silk/satin version is $380 while the leather version is $409.

 This corset was admittedly not purchased directly from Stormy Leather’s website (so I’m not sure about the quality of their customer service), but I had found this piece at discount from a previous owner and had verified that this was indeed a genuine Stormy Leather style. This corset intrigued me as it seemed to have a slight 18th-century-stays inspired style or silhouette – the very flat front, straighter bustline and conical ribs seemed to be a nod towards an almost “Marie Antoinette” style, and had this corset been made from a light-coloured linen or cotton, and tied at the shoulders with ribbons instead of buckles, this corset certainly would have passed as modernized, hybrid stays (it has more of a hip curve and no tabs at the bottom edge compared to reproduction stays). Nevertheless, the pattern of the corset didn’t work with my body.

For a relatively simple 10-panel corset, there is a lot going on in it: the leather gives it a tough ‘biker’ or nightclub look – yet if you choose, you can thread a pretty pastel-coloured satin ribbon through the decorative grommets in the front panel to soften it and create a juxtaposition. The shoulder straps are adjustable based on your body type and comfort level, and the incorporated roller buckles makes sure that the leather doesn’t get damaged from stress/ abrasion.

The continuously-boned modesty panel is one of my favourite parts of this corset, as it laid nice and flat as I was lacing up – it didn’t wrinkle or warp, and although I had quite a large lacing gap, I felt fully supported partially thanks to the structure of this panel.

If you would like to learn more about the Lombard corset, check out Stormy Leather San Francisco’s online store (NSFW).

Posted on 48 Comments

When to Consider an Overbust Corset – and When to Pass

In the past, I have quickly outlined why, if you would like to wear corset on a daily basis, you may want to start with an underbust corset instead of an overbust – however up until now I haven’t dedicated an entire video to this or had gone over this in detail. In this article I’ll outline the reasons why it’s generally better for a beginner to start with an underbust corset instead of the overbust – but if you’re interested in the possible benefits of overbust corsets, you can scroll down for the Overbust “Pros”. You can watch the video below, or you can read the article below the video which has the same information.

There are five main reasons that a beginner may want to start by wearing underbust corsets rather than ovebusts, especially if they plan to waist train:

Overbust Con #1: Reduced Mobility

Overbust corsets are obviously longer and come up higher on the torso – instead of just wrapping around the lower ribcage like an underbust or a cincher would, overbusts extend higher on the chest, and they often wrap around the back as high as the wingbones (or higher!). Because of this, overbust corsets allow a more narrow range of motion than shorter underbusts; they reduce your mobility. This means that you may not be able to reach or bend over as much as you normally would, and you have to make greater adjustments to move ‘naturally’ in an overbust. If mobility is required in your job or it’s something that’s important to you, then an underbust or cincher might suit you better. *However, do note that those who have hypermobility issues may actually desire this reduced mobility from an overbust, as it may decrease the prevalence of overextension/ flexibility-related injuries.

Overbust Con #2: Reduced Full Lung Capacity

A corset obviously differs in structure to that of a bra. Most bras out there have a certain amount of elasticity in their band, which expands and contracts each time you take a breath. With a corset, there is no elasticity (or there shouldn’t be), so the corset’s circumference around your ribcage is relatively fixed.

Take a hypothetical female whose chest measures 32 inches when she exhales completely, and 35 inches when she takes in a full breath. She might want to tie the corset to ~33-34 inches around the bust. This is enough to support the breasts while giving you enough space to take a normal, comfortable (tidal) breath. But each time she inhales deeply, and tries to use her absolute, full lung capacity, she might feel a bit of resistance from the corset. And every time she exhales completely, the ribcage may feel a bit loose and she might have the illusion that she’s not properly supported (even though she probably still is). So if you have breathing issues (or you work in an environment where you need your full lung capacity), you might feel more comfortable wearing an underbust corset that stops lower on the ribcage.

Overbust Con #3: More Conspicuous under Clothing

Cupped overbust made by Doris Müller (Corsets & More)
Cupped overbust made by Doris Müller (Corsets & More)

If you plan to “stealth” your corset underneath your shirts (wear your corsets underneath your clothing), then an underbust corset may look more natural. As mentioned before, the way that overbust corsets support the breasts is different from conventional bras today. Most overbust corsets don’t have individual cups the way that bras do, (although I do have a gallery for cupped overbusts here). But these are often expensive, and the vast majority of conventional (non-cupped) overbust corsets simply don’t give the same bust shape under clothing. An overbust corset may flatten the shape of the bust slightly more, and may not give the defined underwire area where you can see where the breast stops and the ribcage begins. It may also lift the breasts higher than bras, or otherwise make the top half of the breast look fuller – and because of this, overbusts can create more cleavage than bras in some individuals – so wearing an overbust corset under a tight or form-fitting shirt will sometimes make it seem obvious that something is different about you. If you are self-conscious about this kind of attention, you might want to simply pair an underbust corset with one of your regular bras, which will give you a slightly less conspicuous silhouette under your clothes.

Overbust Con #4: More Difficult to Fit Properly

Underbust corsets are much easier to fit a wide range of body shapes compared to overbust corsets. First think about how many bra brands and styles are out there, and how many people still need to go custom fit in their bras to get the right support, shape and comfort they desire. Now think about the number of standard size overbusts are out there – this number is much smaller, and they fit a much smaller range of bust sizes in wearers! If the circumference of your bust is more than 10 inches bigger than your corseted waist size (e.g. 34″ bust, and 24″ corseted waist), you can pretty much forget about finding a standard sized overbust that will accommodate your curves. In order to ensure the best possible fit in overbusts, you will have to go semi-custom or fully-custom, and preferably get professionally fitted with one or more mockups to make sure that the bust fits right. There is a lot to consider when fitting the bust! It must be properly sized – not too big, not too small – the fabric must come up high enough and cover as much of the chest as the wearer desires, the bust must be lifted high enough for the wearer’s preference but not too high, there shouldn’t be any spill over at the armpits/ out of the cup/ over the back, etc. etc. Fitting an overbust can be extremely challenging, and even I have quite expensive custom overbust corsets that didn’t even fit me properly in the end because I didn’t get a mockup.

 Overbust Con #5: More Expensive

If your budget dictates that your choices are limited to standard sized corsets, and you are not of “moderate” or “standard” bust size according to the fashion industry, (whatever “standard” is supposed to mean), then underbust corsets will be much more affordable for you. Even in standard sizes, overbust corsets simply cost more than underbust corsets because they require more fabric, they’re using a longer busk and longer bones, it takes more time to sew over the curve of the bust, etc. So, unless you are dedicated to saving up for a properly-fitted overbust corset, or unless you can somehow be compensated for an overbust by your insurance company, then perhaps an underbust corset would be better for your wallet.

 

At this point it probably sounds like I hate overbust corsets or that it’s difficult to find anything good about them, but this is not true! Well-fitting overbust corsets do have some very redeeming qualities, so now we will discuss the possible Pros about these corsets:

Overbust Pro #1: Better Posture Support

Overbust corsets can be ultimately better for your posture compared to underbust corsets. As mentioned above, overbusts come up higher on the ribcage, and often up to the shoulder blades in the back. This means that it’s nearly impossible to lean over and hunch your shoulders in an overbust corset. Short underbust corsets can help support your lumbar area, but I have seen corset wearers who still hunch or round their shoulders. If a corset comes up higher (halfway up the thoracic vertebrae or higher) then this can greatly reduce the risk of forward-rolled, rounded shoulders, and you might see less forward-head posture as well since your spine is “stacking up” properly.

Overbust Pro #2: Possible Upper Back Pain Management/ Curve Correction

Speaking of the spine, overbust corsets might be more supportive for people with upper back pain, or spine misalignment like scoliosis. Click here to read an article about a middle-age scoliosis patient who used a standard-sized overbust corset in conjunction with special exercises to actually decrease the curvature of his spine over time. Now, please be aware that this is a bit controversial, because this patient used himself as a “guinea pig” in this corrective process. Many corset makers will avoid making “corrective” corsets for those with scoliosis. Some of them can specially draft for an asymmetric corset that will fit a scoliosis patient comfortably, but most makers will not want to make corrective corsets unless they’ve trained with an orthopedic technician or have some experience in making medical prosthetics. But if you have a curvature in your upper or thoracic spine, then perhaps an overbust corset – whether corrective or simply supportive – will help support you better and make for a more comfortable experience as you go throughout your day.

Overbust Pro #3: Support for Large and/or Heavy Breasts

Cartoon by Kat Rosenfield

In some parts of the world, breast reductions are covered by insurance if the patient is able to prove that their breasts impede their lifestyle and cause them pain. Some people have breasts so large that they can cause or exacerbate spinal curvature, they can cause inflammation or even snapping of the scalene muscles and surrounding tendons, among other problems. Having very large or heavy breasts can sometimes lead to very serious medical issues, and one way to help prevent or help these issues is to wear an overbust corset. This is probably the most obvious positive application for overbust corsets, and it’s the one reason I hear most often from people wanting to purchase an overbust. The rigid bones and non-stretch fabric from the overbust corset helps to support the breasts 100% from below, with no pressure or tension coming from above the breast or over the shoulder. The weight from the bust is distributed throughout the rest of the corset, eliminating pressure points or strain in a well-fitting corset. 

Now, in a properly fitting bra, it’s said that at least 80% of the support should come from the band wrapping around the back, and very little support comes from the shoulder straps – but it’s a sad fact that strapless bras don’t work for many people; either the bra doesn’t come in their size, they don’t feel secure in one, or the bra doesn’t stay in place. Consider the damage that has already incurred in many women; think about the hunched shoulders and the permanent indentations in their shoulders and the pain that they’re already experiencing. This is where an overbust corset would be of huge benefit, because it is able to securely support the bust from below without the risk of falling down like many strapless bras do, and without the need for shoulder straps.

Overbust Pro #4: Prevention or Management of shoulder injuries or Thoracic Outlet Syndrome

Illustration of TOS. Source: Wikipedia.

Heavy breasts can cause muscle strain and tendon injuries, and they can even lead to Thoracic Outlet Syndrome. The Brachial Plexus is a group of nerves that runs from the neck and clavicle region into the shoulder, arm and hands. It’s part of the thoracic outlet, in the same region, which is a bundle of nerves and blood vessels together. This area can be compressed or stressed from heavy breasts, or a previous shoulder or neck injury, or even repetitive motions like playing an instrument (guitar, drums or violin). Basically, these factors can lead to nerve compression that can lead to a number of symptoms like tingling, numbness and pain in the hands; swelling and circulation isses; it can mimic the symptoms of carpal tunnel or cubital tunnel syndromes and can limit the use or strength of the hands. In extreme situations, other complications can arise as a result of TOS, such as blood clots.

Depending on the severity of thoracic outlet syndrome, it can be corrected with one or a combination of the following: physical therapy, injections (steroids or botox), surgery (often by removing the first rib next to the collarbone, and sometimes cutting the scalene muscles), and in some situations such as TOS caused by heavy breasts, wearing an overbust corset. Preventing and healing TOS may mean that there can be absolutely zero compression or tension around this delicate neck/ shoulder area, so conventional bras with shoulder straps are no longer an option for these patients.

If you’d like to learn more about TOS, here is an easy-to-understand publication by Dr. S. Mackinnon, M.D.

 

Need an Overbust Corset, but Don’t Want to Tightlace? No Problem.

For those that would like to wear an overbust corset to support their heavy bust, improve their upper back pain or help with TOS, but they don’t want to waist train or they’re nervous about the waist compression, the best part about this is that you don’t need to lace very tightly to reap the benefits of breast support or pain relief. So if you think that the use of an overbust corset can help you with any medical issues, I’d highly recommend you talk to your doctor before investing in one. And for those who are currently actively looking for a corset maker that is experienced in fitting heavy-busted clients, feel free to check out this Guided Gallery made just for you.

What are your reasons for wearing an overbust corset, or for avoiding them? Let me know in the comments below!

Posted on 8 Comments

Where to Buy Overbust Corsets with Cups

Note that this post is a copy of the same one under the “Research Corset Brands –> Guided Galleries” menu. It is part of a collection of articles to help corset enthusiasts shop more wisely.

Cupped overbust corsets are often confused with bustiers or Merry Widows, but in the words of Julia Bremble, “a corset with cups is as corsetty as any other corset if it does a corsetty job.” I personally adore my cupped overbusts because they give a more natural silhouette under clothing compared to conventional overbusts (which may flatten the bust or lift the bust too high). Wearing a well-made cupped overbust under clothing looks like you’re wearing a bra, combined with a cinched waist. They work very well under strapless dresses, and in particular vintage shelf-bust dresses.

Those who are particularly heavy-busted may find that a cupped overbust takes considerable pressure off the neck, shoulders and upper back by supporting the bust properly from below and eliminating the need for shoulder straps. If you don’t like the cupped corset aesthetic, I have another gallery featuring corsetieres that make conventional overbusts (without cups) designed specifically to fit top-heavy women.

*Corsetieres, if you have made cupped overbust corsets and you have a photo to submit to the gallery, please feel free to email me here. Safe-for-work photos are preferred. Thank you!

Madame Sher Overbust with Cups, $600 (cupped styles start at $490)
Versatile Corsets Mimosa overbust, $398
Black Cat Corsets “Chocolate 20” corduroy cupped overbust, R$ 600
Morgana Femme Couture MF1305 cupped overbust, starts at £350
user_63_sg_9
Corsets & More cupped overbust as part of a wedding gown
Cupped and corded overbust by Lost in Wonderland Lingerie & Corsetry
Bizarre Design overbust with cups in leather, starts at €660 (about $900)
Royal Black "Queen of the Night" outfit, starts at €1799
Royal Black “Queen of the Night” outfit, starts at €1799 (about $2450)
Ferrer Corsets “Crimson Passion” overbust with cups, R$ 2790 (Ferrer’s cupped overbusts start at R$ 570)
JC Creations Amsterdam (Click through to see more cupped overbusts, NSFW)
JC Creations Amsterdam (Website is NSFW)
Sinner Couture “Hellbilly Chic” cupped overbust, $450
Anachronism in Action bra-cup-style overbust, custom starts at $435
Anachronism in Action bra-cup-style overbust, custom starts at $435
Cherries Pin-Up Picnic overbust corset with cups by The Bad Button
Ivy Rose Custom Designs hand-dyed cupped overbust (click the photo to see the construction process!)
Totally Waisted! corsets cupped overbust, $900
Totally Waisted! Corsets cupped overbust, $900
Period Corsets c.1950 Stevie Corset, $362
Period Corsets c.1950 Stevie Corset, $362
Orchid Corsetry
Orchid Corsetry “Belle Dame” cupped overbust, Gilded Cages collection
“Alexis” wedding corset, by The Ardent Collection
Luxtenbrae “Aria” overbust with padded, moulded cups
Sparklewren cupped sheer overbust (only available for in-person fittings). Photo: InaGlo, Model: Ivory Flame

*Please note that I have not personally tried every corset brand in this list, nor do I necessarily endorse every company in these guided galleries. This is for informational purposes only; please email any of the above makers to learn more about their corsets.

Posted on Leave a comment

Corset Connection (Versatile) Scarlett Overbust review (& comparison)

This entry is a summary of the review video “Versatile/ Corset Connection Scarlett Overbust Review (and Comparison!)”. If you want visual close-ups and further details, you can watch the video on YouTube here:

Fit, length Center front is 14″, the longest part from peak of the bust to lap is just under 16″.  Gentle sweetheart neckline, not too long on the hips – good for average to long waists. Definitely modern slim silhouette. The bust is 6″ bigger than the waist (suitable for smaller busts, A – small C cup), and the hips are about 10″ bigger than the waist.
Material 3 main layers – the outer fashion fabric is satin, stabilized/ fused for strength, lined in polyester fabric.  Newer versions are lined in herringbone coutil for custom commissions (the blush piece I showed was a display sample so lined in twill)
Construction 6-panel pattern (12 panels total). One version has sandwiched boning channels and a floating fashion layer. Depending on your request, either method of construction can be used (this method or the external boning channel method).Same basic pattern. The other version has topstitched panels, external boning channels, no floating fashion layer.
Binding Binding is made from matching strips of fashion layer material. Binding is machine stitched on both sides. There are also 6 garter tabs; in the old stock, tabs point down while in the new stock, tabs point up.
Waist tape One-inch-wide waist tape running through the corset, either hidden between the layers or exposed on the inside depending on the construction method.
Modesty panel There is a 7.5″ wide modesty panel, attached to one side, covered in matching shell fabric. Also a matching unstiffened front placket.
Busk Busk is 1/2″ wide on each side and 1.5” long, with 6 pins (equidistantly spaced). Reinforced with a flat bone on each side.
Boning 24 bones total in this corset. Double boned on the seams, except for the seam that goes over the bust curve) and then there are two flat steel bones, both ¼” wide sandwiching the grommets and a steel supporting the busk on each side. All flat steel bones (no spiral).
Grommets There are 36 2-part size #00 grommets (17 on each side), with a medium flange, spaced equidistantly. Rolled very nicely, few or no splits, not fraying or popping out.
Laces The laces are 1/8” wide round nylon cord. I find them to be long enough and quite strong, with no stretch – however they can often be slippery.
Price  Currently the Scarlett overbust costs $378 for the standard size. Custom fit is a $90 markup.

Final Thoughts:

Asia DeVinyl models a custom-fit Scarlett overbust

It was an interesting venture to compare the old stock Versatile Corset pieces to the new stock. The old “Antoinette” overbust from Versatile Fashions was renamed the “Scarlett” overbust when the company was sold by Ms. Antoinette over to Corset Connection. And with the changing of hands in the company, there were also a few changes to the way the materials that the corsets were constructed with as well – the current Versatile corsets include fused delicate fashion fabrics for smoothness and strength, a herringbone coutil strength layer (instead of polyester lining), and improved spacing in the grommets.

It’s worth noting that the method of assembly itself hasn’t changed that much. In the video, you can see that the red corset has sandwiched boning channels with an invisible waist tape, while the blush corset has external boning channels and exposed internal waist tape. Both these construction methods are still used today, and depending on the style you order (whether or not you want external boning channels or hidden channels), you may receive your corset constructed either way.

This corset also received 4 stars out of 4 on the Bust Test, as the bust line came up high enough on my chest to hold me in during activity. The bust is designed for smaller cups though, as it pushes everything upward – but it still contains my bust as long as it’s laced loosely enough. However if I were to go back and order this custom-fit, I would certainly request more space in the bust area and perhaps have it “cup” over and above the bust more completely. You can see other styles of the Scarlett corset in Versatile’s photo gallery, on their sale page here.

 

Posted on 2 Comments

“True Corset” Blue Brocade Overbust Review

This post is a summary of the “True Corset” Blue Brocade Overbust Review video, which you can watch on Youtube if you prefer:

Fit, length Front is about 15″ inches long, the longest area (peak of bust to the lap) is 16″, the back is 16″ high. Very shallow/slight sweetheart bustline. I consider this a modern slim silhouette; the bust is 8″ bigger than the waist, and the hips are about 10-11″ bigger than the waist. Recommended for people taller stature or longer waists.
Material 2 main layers: fashion fabric is royal blue brocade, inside has a “bull-denim” style cotton lining (a bit coarser than twill). The internal boning channels are likely petersham ribbon.
Construction 6 panel pattern. Top-stitched between the channels, single boned on the seams, with internal boning channels. 6 garter tabs included as well.
Binding Matching blue brocade bias strips, machine stitched on the outside and inside.
Waist tape 1-inch wide black petersham, exposed on the inside of the corset. It does not extend through all panels though; this waist tape starts between panels 1-2, and ends between panels 5-6.
Modesty panel 5 inch wide modesty panel at the back, unstiffened, attached to one side, and covered in matching blue brocade. Un-boned modesty placket made from black denim under the busk.
Busk 14 inches long with 6 pins (equidistantly spaced). 1/2″ wide on each side (standard width), fairly sturdy.
Boning 14 total bones not including busk. On each side there are three 1/4″ spiral steel bones (in internal channels), but no bone on the seam between panels 4-5. Two further 1/4″ wide flats sandwich the grommets on each side.
Grommets 28 grommets total, size #00 two-part grommets with small flange; set equidistantly. The brocade is fraying around the grommets unfortunately. However the bull denim underneath are still holding the grommets so I will watch them and see if they need replacing. A few split grommets, but doesn’t catch the back.
Laces 1/4″ black flat braided nylon shoe-lace style laces. Virtually unbreakable. Has a bit of spring.
Price At the time that I’m writing, it is £55 in the UK or $80 in the US.

Final Thoughts

Bernie Dexter models the True Corset blue sweetheart overbust
Bernie Dexter models the True Corset blue sweetheart overbust

This overbust is designed for beginners or for those who would like something nice to wear out for a special occasion, as it has an attractive price and an un-intimidating silhouette. I would say that this corset is largely patterned for someone with a small bust/ small ribcage, long torso, and who may be slightly pear shaped as I noticed that this corset had much more room in the hips compared to the bust. I initially went with a size 24″ but I found that it nearly closed at the hips, but at the ribcage and bust I was too large for the corset. However, had I gone one size up to size 26″, although the corset would have been better in the bust and waist, it would have almost certainly been too large in the hips.

As mentioned in the table, the brocade was on the delicate side and began to fray around the grommets. The grommets haven’t pulled out completely, because the sturdy bull denim lining is currently keeping them in place – but I will keep an eye on this corset and see if there are any changes in the future. I have plans to slightly modify this overbust into an underbust in the future, as the brocade is such a beautiful weave but I don’t wear overbusts as often.

You can find the True Corset overbust on their website and also on Amazon.

Posted on Leave a comment

Velda Lauder Bridal Overbust Corset Study

This post is a summary of the “Velda Lauder Bridal Overbust Corset Study” video, which you can watch on Youtube if you prefer:

 

Fit, length Center front is 12.5 inches, and the longest part from peak of the bust to the lap is 14.5 inches. It would be more suitable for a short to average length waist. Interesting sweetheart/plunge bustline, which is cut low on the side and back. I consider this on the border of modern slim/Victorian hourglass silhouette.
Material Likely 2 main layers: fashion fabric is pure white satin – the fashion layer is also the strength layer. (seems to be a thick cotton-backed satin or very-well fused piece), inside is a floating liner of a softer off-white satin.
Construction Technically 5 panel pattern (+ one bust gore in the 2nd panel). Panels assembled using a top-stitch, with grosgrain boning channels laid down under the fashion layer. Floating liner hides the work.
Binding + Embellishment Commercial white satin ribbon, with the edges not folded under. There is another ribbon with attached beadwork, stitched down under most of the top and bottom binding.
Waist tape 1.5-inch wide grosgrain tape invisibly secured between the lining and interlining of the corset; extends across all panels.
Modesty panel 7.5 inch wide modesty panel at the back (about 5.5 inches of useable space), unstiffened, attached to one side, made with white satin.
Busk No busk, only one very thick flat steel bone running down the center front of the corset.
Boning 11 total bones. Single boned on the seams, with very wide bones (I believe 1/2″ wide) and only one supporting bone on the very back edge of the grommets. (The grommets aren’t sandwiched.)
Eyelets 20 grommets total, size #0 single-part eyelets with small to moderate flange; set equidistantly. All the eyelets have rolled nicely, but because there it no back/ supporting washer, there is some concern that an eyelet might come out with rigorous lacing of this corset.
Price I’m not completely sure what this corset was worth when it was still being sold, but I estimate that it would be close to £250 in the UK. (I bought mine for close to half that, because it was a shop/ display sample)

Final Thoughts

Velda Lauder was a well-respected corsetiere, designer, author and educator. You may have remembered when I reviewed her book nearly a year ago, which contained some interesting corset history. Ms Lauder passed away unexpectedly in March 2013; you can read the lovely tribute to her on The Lingerie Addict. After her website was pulled down, I thought I had lost the opportunity to own a piece of her design – until I stumbled across a few overbust corsets in Fairy Goth Mother’s clearance section. I was quite surprised that they were sold for about half price, as I thought the corsets’ relative rarity (now that they’re not longer in production)

The same beautiful white duchess satin curved overbust on a stunning model.

would have caused the corsets to appreciate over time. I didn’t want to pass the chance to own a piece of history.

So this video and study is more meant to be a posthumous tribute and respectful study of a part of Velda Lauder history, rather than a “product review” per se. It is still structured like a review however, if you would ever like to compare side-by-side the construction methods of Lauder’s corsets to others and appreciate the similarities and differences.

Although I must admit that this overbust is not really suited to my body type (and it breaks my heart), I still find many aspects of this corset to be lovely – and quite unique! I think this is the first time I have seen a sweetheart corset that is cut so low along the sides and back – but this allows me to maintain a relaxed posture in the corset and elongate my neck, which is a wonderful feeling (I’m used to looking/feeling like a linebacker in overbust corsets). The thick, 1/2″ wide boning under the seams for the corset were also different, as was the presence of only one bone by the eyelets and not the ‘traditional’ two. I’m sure that many people were equally surprised by the construction of this corset, but it shows that corsets can be made in a multitude of ways, and I’m finding more and more often that notable corset designers don’t play by all the “rules” of corset making! This was one of the most fascinating things about studying corsetry.

Rest in peace, Ms Lauder – thank you for leaving behind such a beautiful legacy that can be studied and appreciated for generations to come.

Posted on 2 Comments

Orchard Corset CS-511 Overbust Review

This entry is a summary of the review video “Orchard Corset CS-511 Overbust Review”. If you want visual close-ups, you can watch the video on YouTube here:

Fit, length Center front is 15″, the longest part from peak of the bust to lap is just under 16″.  Gentle sweetheart neckline, and slightly longline in the hips. This is a Level 3 silhouette, which is their curviest silhouette – so the bust is 8″ bigger than the waist, and the hips are about 10-11″ bigger than the waist.
Material 3 main layers – the outer fashion fabric (which may be brocade, satin etc as I have two different types in this review), flatlined to a sturdy cotton interlining, which is then treated as one layer, and also lined in twill.
Construction 6-panel pattern (12 panels total). Constructed with a slightly modified sandwich technique and double boned on the seams, just like the CS-411 and CS-426 style corsets.
Binding Binding at top and bottom are made from commercial black satin bias strips if the corset is made from a heavier brocade, OR made with matching colored satin if the overbust is finished in a satin fashion layer. Binding is machine stitched on both sides. There are also 6 garter tabs, 3 on each side.
Waist tape One-inch-wide waist tape running through the corset, hidden between the layers. I did not check to see if there was glue used in this one (see my CS-426 review if you want to know more about that particular corset).
Modesty panel There is a modesty panel on the back, made of a layer of black satin and a layer of twill if you have a brocade or tartan corset, but if you buy the blue satin CS-511, then it will be in matching blue satin. Panel is 5.5” wide (~4″ usable space) and attached to one side with a line of stitching. The old stock didn’t have a modesty placket by the busk, but the new stock does.
Busk Busk is 1/2″ wide on each side and 13” long, with 6 pins (the bottom two pins are slightly closer together, as is normal). It is fairly sturdy; less bendy than some other 1/2″ busks I’ve had.
Boning 22 bones total in this corset. On each side, 8 of them are spirals about 3/8 inch wide (double boned on the seams, except for between panels 5-6) and then there are two flat steel bones, both ¼” wide sandwiching the grommets.
Grommets There are 24 2-part size #00 grommets (12 on each side), with a small flange, spaced equidistantly. On the underside of the old stock corsets, every grommet is split and quite scratchy. On the new stock corsets, the grommets have rolled smoothly, they don’t tarnish and don’t catch on the laces.
Laces The laces are ¼” wide flat nylon shoe-lace style. I find them to be long enough and quite strong, but also rather springy. However, Orchard has some higher quality laces (in several colours) available on their website – I very much prefer their ribbon laces to the standard shoelace style laces.
Price Currently $79 USD on Orchard Corset’s website.

Final Thoughts:

It was an interesting venture to compare the old stock Orchard Corset pieces to the new stock. Of all the corset companies that I have dealt with, Orchard seems to be the most responsive to the requests of their clientele and eager to improve their designs, which is appreciated. The main changes to the corsets include the satin having matching modesty panels (not just black satin like in the brocade or Tartan pieces), better quality grommets that don’t tarnish or split as much, and the modesty placket by the knob side of the busk. I believe that their prices have dropped over time as well.

If I could choose only one colour or fabric of the CS-511, I would prefer the tartan more than satin – the sturdy and coarse weave of the tartan makes the corset look less wrinkly, and it’s also more resistant to abrasion and pulls, and feels more heavy weight and sturdy. The stripes in the tartan also match up fairly well – all this makes me a bit sad that this style is now on clearance (but that means that it’s only $59 at the moment, and I’m interested to see what new styles Orchard may bring in the future).

This corset also received 4 stars out of 4 on the Bust Test, as the bustline came up high enough on my chest to hold me in during activity. The pattern around the bust is very gently cupped (meaning it comes up and over the breast, not just pushes everything upward but it contains the bust) so I felt comfortable jumping, shrugging my shoulders, raising my arms and leaning over without feeling like I’m going to pop out.

Orchard Corset has graciously provided my viewers and readers with a non-expiring coupon code – enter CORSETLUCY to receive a 10% discount on your purchase. This corset and the other styles I’ve reviewed (including the CS-411 and the CS-426 underbusts) are available on the Orchard Corset website.

Posted on Leave a comment

Corset Connection (Versatile) Lotus Overbust Review

This entry is a summary of the review video “Versatile Corsets Lotus underbust Review” which you can watch on YouTube here:

Fit, length Front is about 16 inches long, from peak of the bust (longest part) is 18 inches long. Slim silhouette. This is not exactly a longline corset, most of the length is from the waist up so it cups around and covers the bust quite well. Suitable for people with longer waists. The cups may accommodate up to an E cup. However the back was a bit small on me, so this corset may be suitable for those with a larger bust and smaller ribcage. This corset can accommodate about a 12-inch hip spring
Material 3 main layers: the lining is 100% cotton black twill (although custom commissioned corsets from Versatile will contain herringbone coutil lining). Fashion fabric is a heavyweight pink glitter PVC with black accent boning channels.
Construction 5 panel pattern. Twill lining is flatlined/rollpinned to PVC fashion layer; top-stitching between panels (seams are double-stitched at minimum), external boning channels. Also contains 8 garter tabs.
Binding Black binding that matches the external boning channels, made from bias strips of black PVC, folded under on the inside
Waist tape 1″ wide petersham waist tape exposed on the inside.
Modesty panel Attached 8″ wide fabric lacing protector on the back, covered in black satin (more breathable than the PVC or pleather), stitched on one side of the corset; unstiffened placket under busk made from matching black PVC.
Busk Standard flexible busk (1/2″ wide on each side) about 12″ long (6 pins), reinforced with a flat steel bone on each side. An additional 3″ on top of the busk contains grommets to adjust the bust area.
Boning 20 total bones not including busk, all flat (spring) steel bones. On each side they are double boned on the seams, 2 sturdier flats (1/4″ wide) sandwiching the grommets and another flat bone beside the busk.
Grommets 32 grommets total, size #00 two-part grommets with moderate flange; set equidistantly, no splits, no wear/fraying/pulling out of grommets. This type of grommet is my personal favourite used in American-made corsets.
Laces 1/8 inch wide round nylon cord – strong, but slippery.
Price Currently $398 USD for the standard size and basic fabric on the Versatile website. For the glitter PVC, there is a $60 markup.

Final Thoughts:

This is the third of several corsets I will be reviewing for Versatile Corsets/ Corset Connection. The samples were originally agree to be sent back, but the owner of Corset Connection asked me to sell them here on my website (90% funds still go to Versatile) instead of sending them back.

As I mentioned in the video review, this corset passes the bust test with flying colours. There is little-to-no chance of boobling out of this corset, even if you have a long torso, because this corset is so high from waist to

The exact same Lotus overbust on another model with a different body shape, for comparison.

top edge, and the cups are very nicely shaped and they curve up and over the breast to encapsulate it, not just squish it. Despite the fact that this is a relatively modern slim silhouette, I felt like a Barbie doll in this corset (and not only from the pink!). The bust area can accommodate close to a DD/E cup size (as long as the ribcage in the back is relatively small) and the hips accommodate a relatively generous 12-inch hipspring which is indicative of other corsets that are considered quite curvy. Perhaps the length of this corset gives the illusion of “diluting” the curviness.

If I had ordered the Lotus overbust custom made, I would request to have the back just about 2 inches larger to accommodate my ribcage and keep in my back fat/ muffin top. I would likely have ordered it in a lovely brocade instead of PVC – as fun as pink, shiny, glittery plastic can be, I don’t do well with non-breathable synthetic fabrics.

 The Lotus corset (like all the other corsets by Versatile) is available in various colour combinations as you can choose the main fabric, have a choice of lace overlay if you wish, then at no extra charge you can choose a different fabric or colour for the trim, external boning channels, and binding – they can all be different fabrics if you wish! I’m glad that I had the opportunity to see the differences in construction between the various different corsets depending on the styling choices.

Overall, I am glad I had the opportunity to try on this corset; I think of all the Versatile overbusts I’ve tried, this one was my second favourite (next only to the Mimosa cupped overbust). To see other models in the Lotus corset, Versatile has a small gallery so you can see how it fits different people. You can see it on their website here.

Posted on 2 Comments

Versatile Corsets Valerian Overbust Review

This entry is a summary of the review video “Versatile Corsets Valerian Overbust Review” which you can watch on YouTube here:

Fit, length Front is about 16″ inches long, and full length is 17″ over the bust. Modern Elizabethan or slim silhouette (*although please read the Final Thoughts section). A bit of a longline corset; comes over the hips and includes expandable hip ties. Good for women with an long torso; shorter torso probably not advised to wear this unless you get custom sizing. Will accommodate at least E cups, has a demure neckline and built-in off-the-shoulder adjustable straps that can accommodate broader shoulders. Has a high back that gives no opportunity for muffin top.
Material 3 main layers: the lining is 100% cotton American coutil, fashion fabric is a heavyweight satin that is possibly interfaced (I didn’t take it apart) and it has a tulle/lace overlay.
Construction 5 panel pattern. Unique pattern which gives a very flat front yet accommodates a full hip and bust; almost all the panels are angled in a V-shape towards the bottom front. Coutil is flatlined/rollpinned to satin and tulle; top-stitching between panels (seams are double-stitched at minimum), external boning channels. The seams that contain the hip ties are lock-stitched as it helps the seam lay flat and gives a neater finish. Also has 8 garter tabs.
Binding Black binding that matches the external boning channels, made from bias strips of satin.
Waist tape 1″ wide petershame waist tape exposed on the inside.
Modesty panel Attached 6″ wide fabric lacing protector on the back, covered in the same silver satin and tulle overlay, stitched on one side of the corset; unstiffened placket under busk.
Busk Standard flexible busk (1/2″ wide on each side) about 13″ long (6 pins), with a 3/8″ wide flat steel bone on each side. The rest of the length on top of the busk includes grommets to tie at the bustline.
Boning 22 total steel bones not including busk. On each side, 8 spirals (1/4″ wide) double boned on the seams, 2 flats (1/4″ wide) sandwiching the grommets and another flat bone beside the busk.
Grommets 34 grommets total, size #00 two-part grommets with moderate flange; set equidistantly, no splits, no wear/fraying/pulling out of grommets. This corset has a very long back, hence so many grommets.
Laces Strong nylon cord-style laces; they’re thin, strong and they are long enough but quite slippery.
Price Currently $438 USD for the standard size on the Versatile website (right now they’re having a 20% off sale on all their corsets – enter the coupon code FIREWORKS).

Final Thoughts:

This is the first of several corsets I will be reviewing for Versatile Corsets/ Corset Connection. I was so thrilled to have the opportunity to meet the owner of both sister sites, and she was generous to loan me these samples for review. The samples will later be returned and sold at great discount.

I do notice one difference in the construction of this one compared to the Mimosa (which I had reviewed last year) – the waist tape in the Valerian is exposed. I speculate that this difference is due to the Valerian having external boning channels instead of having the bones sandwiched between multiple layers; whereas my Mimosa overbust has the bones sandwiched between multiple layers. If the tape on the Valerian corset were sandwiched between the coutil and the fashion fabric, it may have left an undesirable outline on the outside of the corset.

Aesthetically I do prefer the more dramatic wasp-waist silhouettes, so if I were to go back and buy this again, I may invest in a smaller size. I was not the right model to show off the curves of this corset effectively because it’s a size 26″, and I could probably fit a size 22″ with the proportions of this standard-size corset. It’s very roomy in the bust and the hip ties can accommodate 6-8 extra inches in the hips. To the left you’ll see this exact same corset on a model who fills it out more appropriately.

 The Valerian corset is available in various color combinations as you can choose the main fabric, have a choice of lace overlay, then trim, external boning channels, and binding. I’m glad that I had the opportunity to see the differences in construction between the various different corsets depending on the styling choices.

Overall, I am glad I had the opportunity to try on this corset. Although I usually prefer Victorian, Edwardian or 50’s wasp-waist styles, this Elizabethan-inspired corset was lovely to try on and the construction was a joy to study. I’m tempted to try other Elizabethan-inspired corsets in the future. To see other models in the Valerian corset, Versatile has a small gallery so you can see how it fits different people. You can see it on their website here.

Posted on 1 Comment

Boom! Boom! Baby! Boutique Lace Overbust Corset Review

This entry is a summary of the review video “Boom! Boom! Baby! Boutique Corset Review” which you can watch on YouTube here:

Fit, length Front is about 14 inches long, from peak of bust to bottom (at longest part) is 15.5 inches. Very gentle hourglass shape. Bottom edge is a rounded shape so the corset stops just at the iliac crest (upper hips). Sweetheart bust, and plenty of room in the high back to prevent muffin top. Quite comfortable on me – very curvaceous shapes may want to invest in the upgrade for made-to-measure.
Material Fashion layer is silver/ pewter satin with black lace overlay; backed onto a sturdy strength layer underneath; lining is cotton coutil.
Construction 5 panel pattern. Top-stitching between the panels, single-boned on the seams, and a floating coutil liner (very comfortable). No garter tabs.
Binding Standard black satin bias tape, machine stitched inside and outside.
Waist tape 1″ wide invisible waist tape between the interlining and lining.
Modesty panel Matching 5″ wide modesty panel, made from the same coutil/satin/lace overlay, and also bound in black bias tape. Attached to one side of the corset; removable if desired.
Busk Heavy-duty wide busk (1″ wide on each side) about 13″ long (6 pins).
Boning 12 steel bones not including busk. On each side, there are 4 spiral bones on the seams and another two steel flats sandwiching the grommets at the back.
Grommets 30 grommets total, size #00 two-part eyelets (Prym brand) with moderate flange; set equidistantly; high quality – few splits, no wear/fraying/pulling out of grommets.
Laces Strong cotton braided shoe-lace style laces; they’re thin, they grip well and they are long enough. Very easy to lace up. Zero spring.
Price This particular piece was a one-off (sample) but Kirsteen does take special orders outside of what is available in her store. Most of her corsets on Etsy, made to standard sizes, are advertised as around or under £150, and these corsets can be made to custom measurements for an additional £50. You can see the options on her website here.

Final Thoughts:

This piece is absolutely beautiful. I had seen Kirsteen’s work around the internet for awhile, but I first learned of the name “Boom! Boom! Baby! Boutique” when it was featured in the Lingerie Stylist’s “Top 10 Corsetieres” article in late 2012. Finally had the name of the designer of these fun, circus- and military-themed corsets. Checking out her Facebook page, I stumbled upon an auction of her pieces, and I instantly fell in love with this floral and lace number – not because it was rather different from the pieces normally available in her store, but because it was elegant in and of itself; simply put. I hadn’t yet owned a piece embellished in this way. The fact that it was one-of-a-kind made it that much more special!

I was not disappointed in Kirsteen’s workmanship at all – the stitchwork is neat, the lace overlay doesn’t wrinkle in the slightest, the beaded lace trim and roses are secured with care and attention, the coutil lining inside is high quality, smooth and comfortable. For a piece that was not intended for my measurements, it fits surprisingly well (I feel so fortunate to have these body dimensions). Do not be surprised if you see me review her work again in the future. In fact, I might almost guarantee it. ;)

To see the other styles available by Boom! Boom! Baby! Boutique, visit Kirsteen’s Etsy shop here!

Posted on 1 Comment

Electra Designs Playboy Overbust Corset Review

This entry is a summary of the review video “Electra Designs Overbust Corset Review” which you can watch on YouTube here:

Fit, length Center front is about 16 inches long, from peak of bust to lap is 15 inches. Unique silhouette in which the ribcage follows the natural contours but nips in dramatically at the waist for an dramatic hourglass shape. Hips are cut very high with adjustable hip ties. Plunge sweetheart neckline which supports but doesn’t oversquish.
Material Fashion layer is a heavy salmon-pink satin; strength layer is cotton coutil. No floating liner as it’s a sample piece.
Construction 8 panel pattern. Lock-stitching between panels, stitched 4 times between panels (extremely sturdy). Sandwiched bones, one on each seam and one in the middle of the panel. No garter tabs, but they can be added if you commission a piece.
Binding Matching pink satin, machine stitched outside and hand-finished inside (very neat and clean).
Waist tape 1″ wide waist tape exposed on the inside (because there is no liner. If a floating lining is ordered then the waist tape would be invisible). Secured down in multiple boning channels.
Modesty panel Boned modesty panel suspended on the laces; hourglass shape is very comfortable.
Busk Standard width busk (1/2″ wide on each side) about 13.5″ long (6 pins), two lowest pins closer together.
Boning 24 steel bones not including busk. Flats on either side of the busk and by the eyelets (the eyelets are set into lacing bones), and the rest (on the sides of the body) are 1/4″ spiral steel.
Grommets 28 grommets total, size #00 two-part eyelets with small flange; set equidistantly (they have to be because they’re set into a lacing bone); high quality – no splits, no wear/fraying/pulling out of grommets. Washer on the back is larger than flange for extra support.
Laces Matching pink double-face satin ribbon on the back and also in the front (at bust) and at the hip ties. They glide smoothly through the eyelets, they grip well and they are long enough. Very easy to lace up. Zero spring.
Price The short-hip, sweetheart plunge overbust starts at $469 for standard size and $569 for custom fit. This does not include add-ons like adjustable hip ties, hand-finished binding, or modesty panel. You can see the options on her website here.

Final Thoughts:

This was my second couture corset purchase back around April of 2011 (preceded only by Puimond’s white iridescent overbust). This corset, despite being made for Elegy Ellem (who has a very different overall body composition to my own), fit my measurements surprisingly well. Where I lack in the bust area, I make up for with a broader back.

The adjustable hip ties are wonderful in taking pressure off my left iliac (my main problem when it comes to ordering corsets) and the flexible lacing bones follow the natural curve of my spine, allowing me to hold a neutral posture in this corset – I find that when wearing this corset out to a special event, I’m less tired at the end of the day compared to some of my other overbust corsets which cause a slight change in my posture.

The construction is remarkably strong and the stitchwork is immaculate, even on the inside without a liner. I can’t help but be impressed with each feature of the corset, because it seems that not one decision in construction was made without somehow keeping the wearer in mind. Only Alexis’ busy schedule prevents me from immediately ordering a second piece. She is currently busy creating a multimedia corset making instructional course, which you can learn more about on this page.

To see other styles from Electra Designs, do visit the official website here.

Posted on Leave a comment

Puimond PY15 Black Wicked Plunge Overbust Corset Review

This entry is a summary of the review video “Puimond Wicked Plunge Overbust Review” which you can watch on YouTube here:

Fit, length Center front is about 13 inches long. From apex of bust to bottom of the corset is 17″ (waist to apex 12″), center back about 13.5″. Unique dramatic wasp-waist (yet comfortable) silhouette. Hips are longline and rounded, while ribcage is more conical. Exaggerated plunge neckline; I recommend using double-sided/ toupee tape if your breasts tend to migrate.
Material Fashion layer is black spot broche, backed onto cotton; lining is cotton coutil.
Construction 6 panel pattern. Top-stitching between panels, sandwiched boning channels (with the use of bone casings), one on each seam and one in the center of each panel. Floating liner (very comfortable).
Binding Black patent leather, machine stitched inside and outside; trimmed short instead of folded under on the inside (typical treatment of leather/ pleather binding)
Waist tape 1″ wide invisible waist tape between the interlining and lining.
Modesty panel None.
Busk None. Closed front with embellishment.
Boning 24 steel bones. Two steel flats in the center front (underneath embellishment), and four flats in the back sandwiching the two rows of grommets. Remaining bones are 1/4″ spiral steel, one placed on each seam and one placed in the center of each panel.
Grommets 26 grommets total, size #00 two-part grommets with moderate flange; set equidistantly; high quality – no splits, no wear/fraying/pulling out of grommets
Laces Strong nylon braided shoe-lace style laces; they’re thin, they grip well and they are long enough. Very easy to lace up. Almost no spring.
Price The PY15 is advertised as $490 for fabric and $650 for leather/vinyl. You can see the options on his website here.

Final Thoughts:

This is my second Puimond overbust corset. As I had mentioned in my previous Puimond review, this one is constructed differently and is one of my favorite corsets in terms of fit, comfort and sturdiness. It’s a shame that I don’t get to wear it out often enough!

This corset is quite long with a low waistline, and feels as though it were constructed to fit me, even though it’s a standard size. (The bust is actually supposed to be like that!) The quality of the materials and hardware used are also top. If a standard size fits this well, I’d be quite curious to know how a custom one could fit! I’m a huge fan of Puimond and can’t recommend his work highly enough. To see Puimond’s other styles, do visit his website here.

Posted on 1 Comment

Puimond PY06 Iridescent Pearl Plunge Overbust Corset Review

This entry is a summary of the review video “Sparklewren Couture Overbust Corset Review” which you can watch on YouTube here:

Fit, length Front is about 12 inches long, back is 13″ long. From waist to underbust is 4-5″, waist to peak of bust is about 10″. Unique silhouette in which the ribcage follows the natural contours but nips in dramatically at the waist for an extreme hourglass shape. Hips are cut high; not a problem for pear shapes. Recommended for extreme hourglass ladies. Exaggerated plunge neckline; I recommend using double-sided/ toupee tape if your breasts tend to migrate.
Material Fashion layer is pearlescent vinyl; backed onto cotton; lining is cotton coutil.
Construction 6 panel pattern. Lock-stitching between panels, external boning channels in the middle of the panels, and a floating liner (very comfortable). 6 garter tabs.
Binding Matching pearl vinyl, machine stitched inside and outside; trimmed short instead of folded under on the inside (typical treatment of leather/ pleather binding)
Waist tape 1″ wide invisible waist tape between the interlining and lining.
Modesty panel None.
Busk Heavy-duty wide busk (1″ wide on each side) about 11″ long (5 pins).
Boning 10 steel bones not including busk. On each side, there are 3 bones in the middle of the panels (feels like spiral) and another two steel flats sandwiching the grommets at the back.
Grommets 26 grommets total, size #00 two-part grommets with moderate flange; set equidistantly; high quality – no splits, no wear/fraying/pulling out of grommets
Laces Strong cotton braided shoe-lace style laces; they’re thin, they grip well and they are long enough. Very easy to lace up. Zero spring.
Price The PY06 is advertised as $450 for fabric and $570 for leather/vinyl. You can see the options on his website here.

Final Thoughts:

This was my first couture corset purchase back around February of 2011. I have since purchased another Puimond overbust (PY15) which is constructed differently, and fits totally differently as well. For anyone who may have gotten the impression that I was complaining about the fit of this corset, please note that Puimond is not at any fault – he is a very well-respected designer in this field.

I’m more upset that my torso length doesn’t fit the corset, as opposed to the corset not fitting me. This particular corset was not made to my particular measurements; it has been around for many years and been worn by at least 4-5 different people. It’s held up surprisingly well over time, all things considered. I’m very excited to review my second Puimond corset in the future, as it shows how Puimond alters his construction techniques based on fabrics used and silhouette he’s going for – not all “Puimonds” are the same!

To see Puimond’s other styles, do visit his website here.

Posted on Leave a comment

Sparklewren Couture Overbust Corset Review

This entry is a summary of the review video “Sparklewren Couture Overbust Corset Review” which you can watch on YouTube here:

Fit, length Front is about 10.5″ inches long, unique silhouette in which the ribcage follows the natural contours but nips in dramatically at the waist for a wasp-like effect. Hips likewise follow the body’s natural contours; very comfortable. Longline corset. Will hold in lower tummy pooch, recommended for extreme hourglass ladies. Exaggerated plunge neckline; I recommend using double-sided/ toupee tape if your breasts tend to migrate.
Material Fashion layer is 100% silk charmeuse; interlining is 100% cotton coutil, lining is cotton.
Construction 6 panel pattern. Top-stitching between panels, sandwiched bones, and a floating liner (very comfortable). No garter tabs.
Binding Matching silk charmeuse bias tape, hand-finished.
Waist tape 1″ wide invisible waist tape between the interlining and lining.
Modesty panel Floating 4″ wide stiffened lacing protector on the back; placket by knob-side of busk.
Busk Heavy-duty wide busk (1″ wide on each side) about 10″ long (5 pins), with several bones on each side.
Boning Continuously boned. 64 steel bones not including busk. I’m guessing 58 spirals (ranging from 5mm to 7mm wide) and 6 flats (6mm to 8mm wide) – two on either side of the busk and four sandwiching the grommets at the back.
Grommets 32 grommets total, size 5mm two-part Prym eyelets with moderate flange; set closer together at the waistline; no splits, no wear/fraying/pulling out of grommets
Laces Strong cotton braided shoe-lace style laces; they’re thin, they grip well and they are long enough. Very easy to lace up. Zero spring.
Price Sparklewren has every client sign a confidentiality agreement; please contact Jenni if you would like to commission a similar piece.

Final Thoughts:

This is my second corset purchased from Sparklewren, and my first true experience ordering bespoke from a professional corsetiere. This overbust was commissioned back in January/February of 2012, and completed in May. I was given the option of different colors of silk charmeuse, different types of antique lace and layout of said lace, different flossing motifs, etc. It was an incredibly exciting process and it fits like a dream, too. Jenni is a true artist in her field.
See more of Sparklewren’s creations at her website, here.

Posted on 5 Comments

Versatile Corsets Mimosa Overbust Review

This entry is a summary of the review video “Versatile Corsets Mimosa Overbust Review” which you can watch on YouTube here:

Fit, length Front is about 13.5″ inches long, modern hourglass or slim silhouette. Not a longline corset; cut above the hips. Good for women with an average length torso. May not cover lower tummy pooch – I’d recommend this corset to women who have a balanced figure on top and bottom, or top-heavy women who would like more bust support.
Material 3 layers (counting the interfacing); fashion layer is satin which is interfaced with medium weight woven fusible interfacing, and the lining is 100% cotton American coutil.
Construction 9 panel pattern (6 on the bodice and forming the bust cup). Top-stitching between panels, boning channels are interestingly sandwiched such that the bones are not visible on the fashion layer. Also has 8 garter tabs.
Binding Matching turquoise binding made from bias strips of satin.
Waist tape 1″ wide invisible waist tape between the interlining and lining.
Modesty panel Attached 7″ wide fabric lacing protector on the back; unstiffened placket under busk.
Busk Standard flexible busk (1/2″ wide on each side) about 12″ long (6 pins), with a 3/8″ wide flat steel bone on each side.
Boning 26 (28 if you include the underwire) steel bones not including busk. On each side, 10 spirals (1/4″ wide) double boned on the seams, 2 flats (1/4″ wide) sandwiching the grommets and another flat bone beside the busk.
Grommets 26 grommets total, size #00 two-part grommets with large flange; set equidistantly, no splits, no wear/fraying/pulling out of grommets
Laces Strong nylon cord-style laces; they’re thin, strong and they are long enough but very slippery.
Price Currently $398 USD for the standard size on the Versatile website (right now they’re having a 25% off sale on all their corsets – enter the coupon code Fall25).

Final Thoughts:

When I first bought this corset and received it in the mail, I wasn’t going crazy for it. As time went on, I found that the more I wore it, the more I liked it. The individual cups are very comfortable – I feel that this is one of the few overbust corsets I own that don’t squeeze my girls into painful little pancakes. When working at my computer, I like to wear this corset because it has a natural silhouette and fit (as opposed to a wasp-waist) and the cups support me like a bra, yet take the weight off my shoulders which further prevents me from hunching over.
Aesthetically I do prefer the more dramatic wasp-waist silhouettes however, so if I were to go back and buy this again, I may invest in the custom size. Although the overall effect is flattering as it is, I feel that it would have been an even better fit if the corset were larger in the ribcage, and had smaller cups (C cups instead of D). This would help support my bust more while preventing muffin top around the back. I also feel that the cups could be placed closer together in the front – perhaps the flat bones on either side of the busk can start lower down, allowing the cups to be pushed closer by about an inch.
The Mimosa corset is also available in various color combinations as you can choose the main fabric, then trim, external boning channels, and binding. I’m actually glad that I didn’t get decorative external boning channels, as this gave me the opportunity to see the unique and clever construction – a style I had never seen before:

Overall, I am happy with this purchase. It’s a totally unique piece in my corset collection, and one of the more comfortable overbusts I own. In retrospect I probably should have purchased this corset in a gold color or other earth-tone so I can wear on more occasions in conjunction with a steampunk outfit, from conventions to Halloween. To see other models in the Mimosa corset, Versatile has a small gallery of women of all shapes and sizes so you can see how it fits different people. You can see it on their website here.

Posted on 7 Comments

Glowing Tardis Corset Case Study

This post is a written summary of the video case study for the Light Atop the Tardis corset I made back in May/June of this year.

This corset was made for a girl attending Dragon*Con this August/September so I had to keep it a secret for several months, until after its debut at the convention. The corset itself is supposed to resemble (as its name suggests) the light on top of the Tardis while her skirt was the main box (which opened to show the impossibly huge interior of the Tardis).

-Details of the Tardis corset…>