Posted on 2 Comments

Homemade Corset: Grey Longline Closed-Front Underbust

This entry is a summary of the review video “Showing my homemade corset”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Drafted from Foundations Revealed pattern tutorial. It’s a longline underbust corset with a center front of about 13″ and a waist of about 23″, with an extreme hourglass silhouette. I made the ribcage a little too large so the back seams look like / instead of ||
Material Made out of a black/white fine herringbone weave (I call it grey because that’s how it looks from afar) with gold metallic thread as an outer layer, and one layer of down-proof cotton ticking as a strength layer, which generally doesn’t stretch, but isn’t as strong as coutil.
Construction Drafted from a 5-panel pattern and constructed in the “sandwich” technique in which each layer has its panels individually assembled and then the two layers are attached at the ends, flipped right-side out and then bones are sandwiched between the layers.
Binding The binding at top and bottom are made out of bias strips of the same white/black herringbone fabric.
Waist tape 1-inch wide waist tape, invisibly stitched between the two layers. It’s slightly tighter than the panels of the corset which is what causes the “groove” around the waistline of the corset.
Modesty panel None.
Busk None, this was before I knew where to buy busks (other than the overpriced ones at anime conventions) so I made this with a closed front
Boning 22 bones including the bones at the center front; I had used 1/2″ wide hoop steel for the center front and by the grommets, and 1/4″ wide flats double-boned at each seam. These particular flats were flimsy, which is how I got the silhouette without resistance to the bones.
Grommets There are 24, 2-part size #X00 grommets (12 on each side), finished in gold (the only colour I could find at the time). The grommets have a small size lip around. One of the grommets later popped out at the waistline.
Laces Flat cotton braided shoelace-style laces bought at Timeless Trends; 7 yards long. They grip well, have no spring and are very easy to tighten, however they do snap after about a year of regular use.
Price Cost me probably around $40-$50 in materials, and around 24 hours total to make – this was my 3rd corset so I was still moving very slowly through the steps.
Posted on 6 Comments

My First Corset

Modeling the same corset (around 2005)

This entry is a summary of the review video “Case Study: My First Corset”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Made from Simplicity 9769 pattern. The pattern is larger than expected, so I recommend grading it in at the waist if you want an accurate reduction. Demibust, not longline. Has some slight curve – it was supposed to be a Victorian hourglass shape but it stretched in places. The center front is about 14”.
Material Made out of a single layer of a bedsheet, which has stretched over the years. The fabric is now more transparent. One part of the material ripped when I was letting out the seams and I was a little too vigorous with my seam ripper.There are some pink marks stained on the fabric from using sidewalk chalk instead of tailor’s chalk to mark the seams.
Construction This was my first time flat-felling seams. Internal boning channels made from 1-inch wide twill tape folded over double and sewn down.
Binding The binding at top and bottom are white cotton bias tape.
Waist tape None.
Modesty panel None.
Busk Standard flexible busk,  about 12″ long. I didn’t double-stitch it so it started popping out. I had to repair it several times with an overcast stitch. One of the loops are now bent from too much stress.
Boning 22 bones not inlcuding busk; I cannibalized a vintage corset it for its flat steel bones. Some of the steel bones were too short, and so I doubled up the boning with plastic featherweight boning along the full length of the channel, and then just the metal bit in the very centre of the bone at the waist. This is why you saw the corset buckling in places like in the demibust area when it was on.
Grommets There are 30, 2-part size grommets (15 on each side), finished in nickel. The grommets are sturdy with small size lip around. One of the grommets popped out at the waistline.
Laces White round nylon braided cord style. It has no spring, but tends to catch on grommet edges. Cuts into my hands when I’m tightening the corset.
Price Cost me probably around $35 in materials. As an end product, I would probably have to pay you to take it.
Posted on 2 Comments

CorsetDeal Waspie Underbust Review

This entry is a summary of the review video “Waspie Underbust Review (Corset-Story/Corsets-UK)”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Has very little curve; gives me a more tubular/cylindrical shape than an hourglass. The center front is 11”. The shortest part at the side is 6.5″. Very short, does not come over the hips at all. Even so, I wouldn’t recommend this for people with wide hips.
Material Two layers; the outside heavy polyester satin fabric, and the inside cotton twill.
Construction 6 panel pattern. Panels are top-stitched at the seams, and then internal boning channels laid down, made of black twill.
Binding The binding at top and bottom are black polyester bias tape. Also has 6 garter tabs, but I advise not wearing garters with this corset as it’s so short.
Waist tape Waist tape running through the corset, seen on the inside, made of 1” wide single-faced satin ribbon.
Modesty panel Unboned modesty panel, 6.5 inches wide made from polyester pinstripe on the outside and black twill on the underside. No placket beneath the busk.
Busk Slightly heavy duty, almost 1″ on each side. Stiffer than a standard flexible busk. 10″ long with 5 pins.
Boning 14 steel bones in this corset not including the busk. Single boned on the seams; all the other bones in this corset are spring steel.
Grommets There are 16, 2-part size grommets (8 on each side), finished in nickel. The grommets are sturdy with moderate size lip around, there is some pulling away of the fabric on the grommets around the bunny ears at the waist.
Laces Black round nylon braided cord style. Very strong, although fairly slippery. It has no spring. They are resistant to fraying and catching.
Price Currently ranges from $40 USD – 70 USD (£25 to £45 in UK).
Waspie as it appeared in their product listing

Final Thoughts:

Many moons ago, I bought an underbust corset (“Candy” style) from Corsets-UK. I think I tried it on perhaps twice before selling it, because I felt that my solar plexus was being crushed and my hips lost all circulation. I decided to give this company the benefit of the doubt by trying their Waspie underbust a bit more than a year later, to see if their pattern had improved – maybe this one would be curvier, or more comfortable since it’s cut higher on the hips. I was disappointed. I know that many customers are very happy with this company’s corsets, and if you have the body to pull off this style, then that’s great. However I have to say that this corset did not suit my body type. It didn’t flatter me, and when I had altered it to make it more flattering to my body type, the grommets gave out soon after. I’m sad to say that I doubt that I’ll order from this company again. 

For those interested in trying a corset from CorsetDeal, I’ve found a coupon for 20% off anything on the CorsetDeal site here (aff link).

Posted on 5 Comments

CorsetDeal Longline Overbust Review

This entry is a summary of the review video “Longline Overbust Review (CorsetDeal/Corsets-UK)”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Gently curved, gives a slim silhouette without a lot of cinch. The center front is 15.5”. The longest part of the corset at the apex of the bust is 18”. Sweetheart neckline. Longline corset, ending low over the hips.
Material Two layers; the outside heavy polyester pinstripe fabric, and the inside cotton twill.
Construction 6 panel pattern. Panels are top-stitched at the seams, and then internal boning channels laid down, made of black twill.
Binding The binding at top and bottom are black polyester bias tape. Also has 6 garter tabs
Waist tape Waist tape running through the corset, seen on the inside, made of 1” wide single-faced satin ribbon.
Modesty panel Unboned modesty panel, 8 inches wide made from polyester pinstripe on the outside and black twill on the underside. No placket beneath the busk.
Busk Slightly heavy duty, almost 1″ on each side. Stiffer than a standard flexible busk. 14″ long with 6 pins.
Boning 14 steel bones in this corset not including the busk. Single boned on the seams. The two bones that curve over the bust are made of spiral steel; all the other bones in this corset are spring steel.
Grommets There are 32, 2-part size #0 grommets (16 on each side), finished in nickel. The grommets are sturdy with moderate size lip around, there is absolutely no fraying around the material, they’re not pulling out.
Laces Black flat nylon braided shoe-lace style. Very strong, grips fairly well. It has a little bit of spring. They are resistant to fraying and catching.
Price Currently ranges from $40 USD – 85 USD (£25 to £54 in UK).
The longline overbust pattern product photo, so you can see how it fits a different body type. This is the black brocade fashion fabric rather than the pinstripe, but the pattern and construction are the same. Search for the pattern name “Navya” (aff link).

Final Thoughts:

After experiencing the unflattering way the shorter Corsetdeal overbusts barely covered my girls, I opted for a longline style instead. This was a slightly better fit. I definitely felt that my bust was more secure, and the position of the waist tape was in a more reasonable place, although still not right at my waistline (it was sitting perhaps an inch above my natural waist).

The pattern for the overbust corsets have the same bust/waist/hip circumference as the pattern for the regular overbusts, so keep this in mind. It’s as if they took the original pattern and simply stretched it out vertically to elongate it (i.e. what they did not do, was theoretically take the original pattern and extrapolate the lines to longer [and wider] top and bottom edges). I hope at explanation made sense – if not I will draw a diagram for you all. How this translated to fit on me, is that it fixed the flaring issues that I had at the hips in my shorter overbust corsets, but it resulted in the appearance of a less curvy corset overall. Therefore I recommend this corset to buyers who are tall/ have a long torso, and are either slim/ruler shaped, or slightly apple shaped. If you are a pear or natural hourglass shape, there is a possibility that this corset may not be curvy enough for you.

I didn’t have any problems on my hipbones here in terms of the pattern itself, although the placement of the internal bones at the side seams was unfortunate, as the rigid spring steel bones sat right over a nerve on my iliac crest, causing some chafing and discomfort. The problem was partially resolved by simply replacing the flat bones on the sides with more flexible spiral steel boning, which was a surprisingly easy operation.

For those interested in trying a corset from CorsetDeal, I’ve found a coupon for 20% off anything on the CorsetDeal site here (aff link).

Posted on 1 Comment

CorsetDeal Steampunk Overbust Review

This entry is a summary of the review video “CorsetDeal Steampunk Overbust Corset Review”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Gently curved, gives a slim silhouette without a lot of cinch. The center front is 14”. The longest part of the corset at the apex of the bust is 14.5” so it’s a VERY gentle sweetheart neckline, barely any difference in height from center front to top of bust. Fits like a demi-bust on me and not a longline corset.
Material Two layers; the outside heavy polyester brocade and the inside cotton twill. The binding and decorative external channels are faux leather.
Construction 6 panel pattern. Panels are top-stitched at the seams, and then internal boning channels laid down, made of black twill. The external faux-leather boning channels are simply decorative and have no bones. The buttons and chains on the side are finished in Antique Brass and they’re set into grommets which means that it shouldn’t fall off like other sewn-on buttons do.
Binding The binding at top and bottom are faux leather. Folded under on the front, but on the inside it’s just stitched down and the raw edge is visible. This is typical of leather or PVC type binding as it reduces bulk. Will not fray.
Waist tape Waist tape running through the corset, seen on the inside, made of 1” wide single-faced satin ribbon.
Modesty panel Unboned modesty panel, 7 inches wide made from brocade on the outside and black twill on the underside. There is also a 2 inch wide unboned placket under the front fastener, made from the same fabrics.
Front Closure (Swing hooks) NO BUSK!  There is a flat bone 3/8” wide on either side of the opening in the center front, where these large swing hooks were fastened. I believe that they could have added 1 more set of hooks in the front and spaced them closer together, as I’m noticing that the bones at the waistline are wanting to bow out slightly. For this reason (and because of the mild curves of the corset) I recommend getting this corset only 2-4 inches smaller than your natural waist even if you are able to cinch down more than that.
Boning 14 steel bones in this corset not including the center front. Single boned on the seams. The two bones that curve over the bust are made of spiral steel; all the other bones in this corset are spring steel.
Grommets There are 24, 2-part size #0 grommets (12 on each side), finished in antique brass. The grommets are sturdy with moderate size lip around, there is absolutely no fraying around the material, they’re not pulling out like a couple of them were in the taffeta corset.
Laces Brown flat nylon braided shoe-lace style. Very strong, grips fairly well. I find it nice that all the colours in this corset blend well together.
Price Currently £105 in the UK ($165 in the USA).
Current product photo for CorsetDeal’s steampunk “Alba” overbust (aff link)

Final Thoughts:

This was the first style I had seen of the 2012 collection from Corsets-UK/ CorsetDeal, and I was floored. After so many years of the same classic (tired) designs, at last this was something cool, fun, affordable and usable for more situations than just “burlesque dress up” like their frillier options. And in many ways, it was fun and cool – I loved the rich chocolatey brocade, the faux leather trim and casings, the various chains and other hardware… but it was also a bit dangerous on the top edge. I’m wondering if the models the company used on the site was short-waisted (or just short stature) because wow, the corset was kind of low cut on me, and the waist tape was several inches higher than my natural waist. I’ve now seen this corset on other customers; they’re of smaller frame than I am and it looks incredible on them.

This was the first corset I owned that had the swing hooks. My goodness, I love those swing hooks! However I wish that there were 5 of them instead of just 4. I was sort of beginning to see the center front edge beginning to bow out (it could just be the fabric and not the bones) and felt that could have been avoided if the hooks were placed closer together and an additional one were added right at the waist where there was most tension.

As for any actual cinch in this corset, I didn’t experience much. Yes the corset does take me in a few inches on the inside of the corset, but this corset is so heavy and bulky that I don’t really look cinched at all on the outside – so keep this in mind when ordering. This corset is primarily for a fun addition to an outfit, and not suitable for tightlacing or waist training. This style of corset also has about an 8 inch difference between bust and waist – for example, on that 24″ corset, the bust measurement was 32″.

Update: For those interested in trying a corset from CorsetDeal, I’ve found a coupon for 20% off anything on the CorsetDeal site here (aff link).

Posted on Leave a comment

Corsets-UK Overbust “Waist Training” Corset Review

This entry is a summary of the review video “Corsets-UK ‘Waist Training’ Overbust Review”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Gently curved. The center front is 14”. The longest part of the corset at the apex of the bust is a little over 15”. Very straight back, I wouldn’t recommend this for people with swayback.
Material Two MAIN layers, the outer red taffeta and inner black twill, but both have fusible interfacing on the inside.
Construction 6 panel pattern. The seams appear to be lock-stitched, NOT top stitched. The bones are sandwiched between the layers of fabric. The lining is attached to the other layers by stitching in the ditch.
Binding Binding at top and bottom are black taffeta. I would have preferred binding in red to match the rest of the corset. Machine stitched on both sides.
Waist tape One-inch-wide waist tape running through the corset, hidden between the layers.
Modesty panel Unboned modesty panel in the back made from red taffeta on the outside and black twill on the underside. There’s no placket under the busk.
Busk Heavy duty busk, a little less than 1” wide on each side. It’s 12.5” long with 6 pins.
Boning 24 steel bones in this corset. Double-boned on the seams, there are 10 ¼” wide spiral steels on each side, and then sandwiching the grommets are 2 spring steel bones each about 7mm wide.
Grommets There are 24, 2-part size #0 grommets (12 on each side). The grommets are sturdy with moderate size lip around and no obvious splits on the underside. There is some pulling away of the fabric from the grommets at the waist (around the “bunny ears”).
Laces Round braided nylon cords, NOT flat laces as one sees in other brands of corsets. They glide smoothly through the grommets but I find that they don’t grip well, meaning my corset tends to loosen over time. It’s extremely strong, hard to break, but I would rather replace the laces.
Price Currently £72 in the UK ($114 USD).

Final Thoughts

I actually ordered this corset a long time before I finally actually got around to reviewing it. This doesn’t mean that I wore it a lot, though. It was a lovely little piece and I liked how smooth the satin was around my body – prior to this corset, I experienced satin wrinkling up from stress on the corset, particularly at the waist, but it didn’t happen in this situation because it was fused to another layer. That was one thing I did like about it.

The fit of this sweetheart overbust corset is much more comfortable and more flattering than their underbust corsets. In the overbusts, the bust is 8 inches larger than the waist, and the hips are 10 inches larger in the waist. In the underbust corsets, the ribcage is only 4 inches larger than the waist, and the hips 6 inches larger than the waist. Why did they make the hips so much smaller in the underbust compared to the overbust? Anyway, for this reason a lot of people would naturally decide to use an overbust to train in. In my experience, underbust corsets are usually easier to breathe in (since they don’t extend so high up the ribcage), easier for mobility, and easier to hide under clothing. I just wish that this brand’s underbust corsets were curvier! I did try to cut this overbust down to an underbust, and failed miserably because of the way the bones were sewn into the corset and can’t be removed.

Is it theoretically possible to waist train in a Corsets-UK or CorsetDeal “waist training” corset? I have sorta seen it done in the past (there are die-hard Corsets-UK fans out there who don’t use any other brand), but I can’t guarantee that it’s going to be as safe or effective compared to a custom waist training corset. Even the owner of Corset Wholesale said that there’s no point in comparing a $40 corset with a custom made corset. Therefore, don’t expect a cheaper corset to do the same job as a custom one.

Posted on 3 Comments

Ms Martha’s Leather Geometric Cincher Review

This entry is a summary of the review video “Ms Martha’s Leather Geometric Cincher Review”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Center front is 12 inches, side is 8 inches, cut high on the hip and doesn’t pinch.I have a size Medium and it has a waist of 22 inches. Small has a waist of 18″; each size increases in increments of 4″. I advise you to order the size for your natural waist, or up one size if you’re on the upper end of a size.
Material Leather fashion layer, cut in a ribbon-corset style with horizontal panels. The inner layer is twill. I had to air out the leather for a week before the factory smell dissipated enough for wear.
Construction 5 main panels – 2 of them create most of the shape with horizontal stitching, while the vertical panels hold the hardware and boning. Floating liner inside, and 6 garter tabs.
Binding Black leather; folded under on the front and then clipped short on the underside – common in leather or vinyl binding to minimize bulk.
Waist tape None –  typical of a ribbon-style corset. Ms Martha says her corsets are not for tightlacing.
Modesty panel MASSIVE 10-inch wide back panel that has a single bone running vertically down the center. Leather on the outside and twill on the inside. Also has a 2″ wide leather placket in front.
Busk 11-inch long, heavy duty busk – one inch wide on each side. Quite a bit stiffer than the standard flexible busk.
Boning Total of 8 bones in this corset. 2 spirals on each side seam and 2 spring steels sandwiching each line of grommets in the back.
Grommets 24, 2-part size #0 grommets. These grommets and the washers both have a very large lip which I like. The inside of the grommets have a few very tiny splits, but it’s forgivable because it doesn’t catch on the laces.
Laces Flat braided nylon shoelace style in black; they have a little bit of spring to them. Bulky, so they don’t glide through the grommets quite as well as a thinner one would, but it’s still very strong and very difficult to break.
Price Currently $175 USD in leather, and $170 in silk.
Leather Geometric Cincher from Ms Martha’s Corset Shoppe ($185 USD)

Final Thoughts

This cincher has a beautiful shape – I think it’s one of my favorite shapes of my underbust collection. It is totally comfortable over my hips and feels very secure but not overbearingly tight around my ribs. Because this is made out of leather and twill, I feel that it has stretched out a bit, but not dramatically. Note that the leather did have a strong scent to it when I first opened the package, but I left the corset to air out for a few days in a ventilated room and the smell soon dissipated. Later on I did change out the laces – while the original ones were very strong, it was also quite thick so I experienced a lot of friction when trying to tighten the corset, making it difficult to put on and take off so I simply changed them with thinner shoelaces. But I still own and wear this corset quite often, a year later – you can see it in some of my later videos, like this dressing with your corset post.

Now, be aware that I don’t know what will happen with your corset if you tightlace in this – mine has seemed to hold up fine – but there might be a possibility of a busk pin popping or a seam coming loose, if Ms Martha doesn’t give guarantees that her corsets stand up to tightlacing. I’m just putting that out there.

One thing I want to touch on is the sizing. These corsets run small. When I was looking at the size chart, a Small was recommended for natural waist sizes 20″ – 28″. Since my waist was around 27″ at the time that I ordered, I thought a Small would be great. Ms Martha strongly recommended that I go with a Medium instead. Apparently the size Small has a miniscule waist of only 18″ which was been far too small for me! I later heeded her advice and she was very kind and patient with me about exchanging this cincher. A size Medium has a closed waist of 22″.  So if you are petite or if you are around my size, consider ordering a size up. If you’re naturally on the fluffier side, then you will probably be able to reduce more than me, so order true. This store has the largest range of sizes of any off-the-rack store I’ve found to date, offering corsets for people with waist sizes 18″ up to 52″.

So for your consideration, here is Ms Martha’s size chart that has the “closed waist” corset sizes:

Small Medium Large XL 2XL 3XL 4XL
 18″  22″  26″  30″  34″  38″  42″