Posted on 6 Comments

Camellia’s Corsets: Short Torso Mesh Cincher / Waspie Review

This entry is a summary of the review for the “Camellias Women Petite Steel Boned Waist Trainer Corset Short Torso Mesh Body Shaper” made by Camellia’s Corsets on Amazon. Note: I purchased this corset with my own money and reviewed this of my own volition. Amazon affiliate links help support my site and the price does not increase for you. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

 

Fit, length Center front is 9.5 inches long, the princess seam is 8.5 inches (4.5 inches above the waist, 5 inches below the waist), the side seam is 8.25 inches and the center back is 9 inches long.
I chose the size 24″. When I measured this before wearing, the ribcage was 26.5″ (rib spring of 2.5″), the waist was 23.5″ laid flat, (which stretched to 24″ while I was pulling on it with my hands), and the hip was 30″ (hip spring of 6″).
Material The panels are made from what appears to be 2 different types of mesh, but they’re actually attached to one another. The outer one is a honeycomb, fishnet appearance, which we so often see in many other OTR mesh corsets. The layer underneath is a sort of finer-weave mesh, and it has a bouncy, foamy kind of plush feel. The fabric content says 90% polyester, and 10% spandex so it has some give. The binding and boning channels are thin cotton twill.
Construction 6-panel pattern (12 panels total). Panel 1-2-3 converge downwards, and panels 4-5 create the curve over the hip.
The panels were assembled together with seam allowances facing outside, topstitched on the underside – and then cotton boning channels laid down on the outside, single boned on the seams.
Waist tape One-inch-wide waist tape, made from black single-faced satin ribbon and secured down at each boning channel. Almost full width (extends from serged seam near panel 1, to the boning channel by the back grommets.
Binding Black cotton twill, machine stitched with a slight top-stitch on both outside and inside (may have been done on a single pass). No garter tabs, but there are two loops at the top to hang it from.
Modesty panel Just under 6″ wide, unstiffened, finished in 2 layers of black twill, and attached to one side with a row of stitching.
In the front, there is a 3/4 inch wide modesty placket extending from the knob side of the busk, unstiffened and finished in black twill.
Busk 8.5” long, with 5 loops and pins, equidistantly spaced. Slightly wider than a standard flexible busk, around 3/4″ wide on each side, and about the same flexibility as a standard flexible busk.
Boning 14 bones total in this corset, 7 on each side. Single boned on the seams with ¼ inch wide spirals. The bones sandwiching the grommets are flat steels, also ¼ inch wide.
Grommets There are 18, two-part size #00 grommets (9 on each side). They have a small flange and are spaced equidistantly, and finished in silver. Washers present in the back. The grommets at the waist feel very slightly loose in the back after half a dozen wears (2 inch reduction) but have not fallen out yet.
Laces ¼ inch wide, black, flat, nylon, shoelace style lacing (standard workhorse laces).
Price Available in black mesh and white mesh, both $35 on Amazon.

 

Camellia’s Corsets mesh short torso / waspie / cincher, $34.99. Picture courtesy of Amazon (click through for listing).

Final Thoughts:

I was surprised by the curvy, round-rib silhouette it gave, but the fabric is quite moldable to the body because the label states it’s 10% spandex. Although the binding and the waist tape hold the top edge, waist and bottom edge from stretching too much, it definitely has a lot of give.

My corset measured a bit small in the waist when I initially received it, but I could also tell that it did expand over time as I wore it in more – so perhaps they deliberately run a bit small in anticipation of some stretch. If you need considerable mobility, this piece will provide you with that, but expect some ease to also occur over time.

One part I wasn’t aesthetically crazy about was the fact that the fabric gave too much at the boning channels, allowing the steel bones to “flare” away from the body (especially at the hips), creating little spots where they poke out. This gives the impression that the corset isn’t pulled taut against the body, when really the binding is quite snug against my hips but the bones simply don’t lie flat.

Also, the waist tape was found to be uneven on each side at the center front – I would have cared if it were uneven in the back, but as the flaw is front and center, this is unfortunately quite noticeable through the transparent mesh.

The fabric by the back grommets and around the busk seems to not be reinforced with any interlining, which is a concern for longevity. I do see that the grommets are shifting slightly over time as I’ve worn this corset in, although none have fallen out yet. Camellia’s Corsets only recommends 2-3 inch waist reduction in these corsets, so I would not advise this for tightlacing, but more for a temporary gentle cinch and fashion use.

Learn more about the cincher on Amazon.

Posted on

What Katie Did Vamp Corset Review

This entry is a summary of the video “What Katie Did (WKD) Vamp Corset Review”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

 

Fit, length Center front is 11 inches long, the princess seam is 9 inches (4.5 inches above the waist, 4.5 inches below the waist), the side seam is 10 inches, and the center back is 11.75 inches long.
Rib spring is 7″, low hip spring is 13″. The rib is conical, and the hip spring is rounded / shelf-like and dramatic.
Material 3 main layers – the fashion fabric aubergine silk and contrasting pewter brocade (see Final Thoughts below), it has a cotton twill strength fabric, and it’s lined in black cotton twill as well.
Construction 7-panel pattern (14 panels total) including hip gores. Fashion fabric was flatlined to strength fabric, panels were assembled, and external boning channels laid down overtop. The lining is floating.
Waist tape 1-inch-wide waist tape, usually installed “invisibly” between the layers. This corset has an external waist belt which is aesthetic and also functional.
Binding Made from strips of pewter brocade, machine stitched on outside and inside (topstitch on both sides, may have a special attachment that stitches on the binding in one pass). Also has 6 garter tabs, 3 on each side.
Modesty panel Nearly 8″ wide, unstiffened, finished in aubergine silk (fashion fabric) and lined in cotton. Attached to the corset (sewn into the lining of the corset, so can’t easily be removed).
In the front, there is a 3/8″ wide placket under the knob side of the busk, slightly stiffened (buckram?) and finished in matching raw silk.
Busk 10 inches long, with 5 loops and pins, equidistantly spaced. 3/4″ wide on each side (slightly wider than a standard flexible busk), with an adjacent flat steel on either side of the busk for extra stiffness.
Boning 18 bones total in this corset, 9 on each side. Some seams are single boned and some seams are double boned, depending on how much space there is (perhaps the larger sizes have more bones?). The bones on the seams are all ¼ inch wide spirals. The bones sandwiching the grommets are ¼ inch wide flat steel, as well as the bones by the busk.
Grommets There are 22, two-part size #0 grommets (11 on each side). They have a medium flange and are spaced equidistantly, and finished in silver.
Laces The laces are black, 3/8 inch flat nylon shoelace. They have a little spring, they’re difficult to snap, they hold bows and knots well, and they are long enough.
Price Available in size 18″ up to 34″.
Price starts at £169.50 GBP ($275 USD) for the classic Vamp in solid satin colors, and price may go up from there depending on what you choose in their “Designer” section.

 

Final Thoughts:

WKD Vamp corset in black satin.

Of all the underbust corsets from What Katie Did, this might just be my favorite. It’s just as curvy as the Morticia underbust, but made to be a more “squat” version so you get all the curve in less of the length. It provides the look and support of a longline corset while still allowing those with a shorter waist (or shorter of stature) to sit down comfortably.

True to WKD aesthetic, it’s quite conical over the ribs, dramatic over the hips, and gives a very flat tummy, making it ideal to wear under retro clothing.

 

I chose the color and overall design of this Vamp corset by submitting my choices in their Corset Designer – for the fashion fabric, I chose a rich, deep aubergine raw dupioni silk, and I requested external boning channels, binding and an external diamond waist tape all made from a pewter / gunmetal (dark silver) floral brocade. You can choose different colors or fabrics for all of these components, or you can choose to not have any contrasting channels or any belt at all (you do need binding, but you can have it match the rest of the corset). Ordering a special design corset automatically makes the corset a WKD Gold Label corset.

Do keep in mind that their “Design your own Corset” section is mainly for colors, fabrics, embellishments and trims for a selection of their standard sized corsets, and it does not give a made-to-measure option. They can make corsets 1 inch longer or 1 inch shorter at the top / bottom edge compared to the base pattern, but this is the extent of the pattern changes they’re able to do.

What Katie Did’s Vamp corset can be found on their website here.

EDIT 2018: What Katie Did has discontinued the Vamp corset and has created an entirely new line of corsets! The probable equivalent of their old Vamp is their new Extreme Morticia Nouveau corset.