Posted on Leave a comment

Baby Blue Ribbon Cincher Case Study

This entry is a summary of the review video “Homemade Blue Ribbon Corset”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Short cincher about 12″ high in the center front, comes up high on the hips. Pointed in the front and in back.
Material Almost entirely 2.25″ wide double faced satin ribbon, with coutil flatlined to the ribbon on the vertical panels in front, side and back.
Construction Pattern is from page 88 of the book Corsets and Crinolines. The horizontal ribbons were draped into the correct shape and tacked on the sides, then sandwiched between two pieces of coutil-flatlined-to-ribbon vertical panels which were then topstitched. The bones sandwiched in the vertical panels only.
Binding There is only binding at the top and bottom of the vertical panels, also made with blue ribbon.
Waist tape None (ribbon corsets generally don’t have waist tapes).
Modesty panel None.
Busk Standard flexible busk, about 9.5″ long with 5 clasps.
Boning 14 bones in this corset; 8 bones on the side panels (4 on each side), 2 flats on either side of the busk and another 4 in the back sandwiching the grommets.
Grommets 26 gold #X00 2-part grommets (13 on each side). Gold was the only colour I had at the time.
Laces Simple white round shoe-lace style cord, about 7 meters.
Price Cost in materials was close to $35. A standard ribbon cincher is often sold for about $150-$200 depending on the maker. Custom fit ribbon cinchers often are more expensive.
Posted on Leave a comment

Princess Tamina Corset Case Study

This entry is a summary of my videos for the Princess Tamina costume. If you would like more  information and side notes about the corset and costume, you can watch the videos on YouTube here:

 

 

Fit, length Self-drafted underbust corset with a peaked front top and bottom edge. Stops just at the hips, and features a high back (7″ above waist). Made to close at 21″ at the waist. I took 3 horizontal measurements and 5 vertical measurements to draft this.
Material 4 layers of material; fashion fabric is a very stretchy gold-on-beige lamé, two layers of down-proof cotton ticking (labelled “coutil” in French) as strength layer, and ivory satin lining.
Construction Drafted from a 5-panel pattern. Lining was flatlined to ticking and lockstitched between the seams, then joined to another layer of ticking (wrong sides together) via the sandwich method. Sandwiched boning channels were sewn through those 3 layers, then the fashion fabric was redesigned to look like a ribbon corset and was tacked down at center front and back seams; floating in all other places. Embellishment was hand-sewn.
Binding Made from bias strips of lamé and machine stitched on both front and back. Back of binding was not folded under but left raw; as it’s a knit it doesn’t fray.
Waist tape 1-inch wide waist tape, invisibly stitched between the two layers of ticking.
Modesty panel None.
Busk None; closed front.
Boning Only 12 bones including center front; all half-inch wide steels. Two at center front and one on each seam between panels; only a bone on the outer edge of the grommets, not the inner edge.
Grommets There are 22, 2-part size #X00 grommets (11 on each side), finished in gold to match the rest of the corset. This corset being the first time I hammered in grommets, the back of some of them are rough and catch a bit on the laces.
Laces Round nylon utility cord made for outdoor/sports use. It was loosely woven, frayed easily, slippery and didn’t hold bows very well.
Price The cost for materials was close to $70 because the only store that supplied steel bones near me charged me an arm and a leg for them. Otherwise this corset would have been closer to $35-$40 in supplies. If I were to remake this corset today and sell it, it would cost around $315 USD.
($225 underbust corset + $15 half-inch boning upgrade (I’d use spiral at seams) + $20 double (proper) coutil strength layer upgrade + $40 pattern modification + $15 hand-sewn embellishments)
Posted on Leave a comment

Grey & Green Longline Underbust Case Study

This entry is a summary of the review video “Grey & Green underbust case study”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Self-drafted, longline (low over the hips) underbust corset with a peaked front top and a straight bottom edge. Made to close at 22″ at the waist. I took 5 horizontal measurements and 9 vertical measurements to draft this.
Material Fashion fabric is a black/white fine herringbone weave with metallic gold thread pinstripes This was fused to herringbone coutil interlining and lined in fern green satin.
Construction Drafted from a 6-panel pattern and both topstitched and lockstitched for extra strength. Boning channels are external (made from green satin fused to coutil) and the lining floats.
Binding The binding at top and bottom are made from 2-inch-wide strips of green satin, machine stitched on both sides.
Waist tape 1-inch wide waist tape, invisibly stitched between the coutil and the lining.
Modesty panel Suspended modesty panel stiffened with plastic canvas and finished the same way as the corset – covered in the pinstripe fabric and bound with green satin on top and bottom.
Busk Heavy duty stainless steel busk (1″ wide on each side) and was cut to 13″ long, with 5 pins.
Boning 20 bones not including the busk; I had used 1/4″ wide spirals double-boned at each seam (except the one adjacent to the busk) in the external channels. By the grommets there’s a 1/2″ wide flat bone on the outer edges and 1/4″ wide flat bone on the inner side.
Grommets There are 32, 2-part size #0 grommets (16 on each side), finished in silver (Chelsea’s choice). The grommets have a large lip around and are spaced 3/4″ inch apart down the length.
Laces Flat nylon braided shoelace-style laces; 8 yards long. They grip well, are densely woven and are resistant to catching, fraying or snapping.
Price The retail price for something similar is around $280 (underbust corset + heavy busk upgrade + double boning upgrade + external boning channels upgrade).
Posted on 2 Comments

Homemade Corset: Grey Longline Closed-Front Underbust

This entry is a summary of the review video “Showing my homemade corset”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Drafted from Foundations Revealed pattern tutorial. It’s a longline underbust corset with a center front of about 13″ and a waist of about 23″, with an extreme hourglass silhouette. I made the ribcage a little too large so the back seams look like / instead of ||
Material Made out of a black/white fine herringbone weave (I call it grey because that’s how it looks from afar) with gold metallic thread as an outer layer, and one layer of down-proof cotton ticking as a strength layer, which generally doesn’t stretch, but isn’t as strong as coutil.
Construction Drafted from a 5-panel pattern and constructed in the “sandwich” technique in which each layer has its panels individually assembled and then the two layers are attached at the ends, flipped right-side out and then bones are sandwiched between the layers.
Binding The binding at top and bottom are made out of bias strips of the same white/black herringbone fabric.
Waist tape 1-inch wide waist tape, invisibly stitched between the two layers. It’s slightly tighter than the panels of the corset which is what causes the “groove” around the waistline of the corset.
Modesty panel None.
Busk None, this was before I knew where to buy busks (other than the overpriced ones at anime conventions) so I made this with a closed front
Boning 22 bones including the bones at the center front; I had used 1/2″ wide hoop steel for the center front and by the grommets, and 1/4″ wide flats double-boned at each seam. These particular flats were flimsy, which is how I got the silhouette without resistance to the bones.
Grommets There are 24, 2-part size #X00 grommets (12 on each side), finished in gold (the only colour I could find at the time). The grommets have a small size lip around. One of the grommets later popped out at the waistline.
Laces Flat cotton braided shoelace-style laces bought at Timeless Trends; 7 yards long. They grip well, have no spring and are very easy to tighten, however they do snap after about a year of regular use.
Price Cost me probably around $40-$50 in materials, and around 24 hours total to make – this was my 3rd corset so I was still moving very slowly through the steps.
Posted on 6 Comments

My First Corset

This entry is a summary of the review video “Case Study: My First Corset”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Made from Simplicity 9769 pattern. The pattern is larger than expected, so I recommend grading it in at the waist if you want an accurate reduction. Demibust, not longline. Has some slight curve – it was supposed to be a Victorian hourglass shape but it stretched in places. The center front is about 14”.
Material Made out of a single layer of a bedsheet, which has stretched over the years. The fabric is now more transparent. One part of the material ripped when I was letting out the seams and I was a little too vigorous with my seam ripper.There are some pink marks stained on the fabric from using sidewalk chalk instead of tailor’s chalk to mark the seams.
Construction This was my first time flat-felling seams. Internal boning channels made from 1-inch wide twill tape folded over double and sewn down.
Binding The binding at top and bottom are white cotton bias tape.
Waist tape None.
Modesty panel None.
Busk Standard flexible busk,  about 12″ long. I didn’t double-stitch it so it started popping out. I had to repair it several times with an overcast stitch. One of the loops are now bent from too much stress.
Boning 22 bones not inlcuding busk; I cannibalized a vintage corset it for its flat steel bones. Some of the steel bones were too short, and so I doubled up the boning with plastic featherweight boning along the full length of the channel, and then just the metal bit in the very centre of the bone at the waist. This is why you saw the corset buckling in places like in the demibust area when it was on.
Grommets There are 30, 2-part size grommets (15 on each side), finished in nickel. The grommets are sturdy with small size lip around. One of the grommets popped out at the waistline.
Laces White round nylon braided cord style. It has no spring, but tends to catch on grommet edges. Cuts into my hands when I’m tightening the corset.
Price Cost me probably around $35 in materials. As an end product, I would probably have to pay you to take it.
Posted on 2 Comments

CorsetDeal Waspie Underbust Review

This entry is a summary of the review video “Longline Overbust Review (CorsetDeal/Corsets-UK)”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Has very little curve; gives me a more tubular/cylindrical shape than an hourglass. The center front is 11”. The shortest part at the side is 6.5″. Very short, does not come over the hips at all. Even so, I wouldn’t recommend this for people with wide hips.
Material Two layers; the outside heavy polyester satin fabric, and the inside cotton twill.
Construction 6 panel pattern. Panels are top-stitched at the seams, and then internal boning channels laid down, made of black twill.
Binding The binding at top and bottom are black polyester bias tape. Also has 6 garter tabs, but I advise not wearing garters with this corset as it’s so short.
Waist tape Waist tape running through the corset, seen on the inside, made of 1” wide single-faced satin ribbon.
Modesty panel Unboned modesty panel, 6.5 inches wide made from polyester pinstripe on the outside and black twill on the underside. No placket beneath the busk.
Busk Slightly heavy duty, almost 1″ on each side. Stiffer than a standard flexible busk. 10″ long with 5 pins.
Boning 14 steel bones in this corset not including the busk. Single boned on the seams; all the other bones in this corset are spring steel.
Grommets There are 16, 2-part size grommets (8 on each side), finished in nickel. The grommets are sturdy with moderate size lip around, there is some pulling away of the fabric on the grommets around the bunny ears at the waist.
Laces Black round nylon braided cord style. Very strong, although fairly slippery. It has no spring. They are resistant to fraying and catching.
Price Currently ranges from $40 USD – 70 USD (£25 to £45 in UK).

 

Final Thoughts:
Many moons ago, I bought an underbust corset (“Candy” style) from Corsets-UK. I think I tried it on perhaps twice before selling it, because I felt that my solar plexus was being crushed and my hips lost all circulation. I decided to give this company the benefit of the doubt by trying their Waspie underbust a bit more than a year later, to see if their pattern had improved – maybe this one would be curvier, or more comfortable since it’s cut higher on the hips. I was disappointed. I know that many customers are very happy with this company’s corsets, and if you have the body to pull off this style, then that’s great. However I have to say that this corset did not suit my body type. It didn’t flatter me, and when I had altered it to make it more flattering to my body type, the grommets gave out soon after. I’m sad to say that I doubt that I’ll order from this company again. 

For those interested in trying a corset from CorsetDeal, I’ve found a coupon for 20% off anything on the CorsetDeal site here (aff link).

Posted on 3 Comments

Ms Martha’s Leather Geometric Cincher Review

This entry is a summary of the review video “Ms Martha’s Leather Geometric Cincher Review”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Center front is 12 inches, side is 8 inches, cut high on the hip and doesn’t pinch.I have a size Medium and it has a waist of 22 inches. Small has a waist of 18″; each size increases in increments of 4″. I advise you to order the size for your natural waist, or up one size if you’re on the upper end of a size.
Material Leather fashion layer, cut in a ribbon-corset style with horizontal panels. The inner layer is twill. I had to air out the leather for a week before the factory smell dissipated enough for wear.
Construction 5 main panels – 2 of them create most of the shape with horizontal stitching, while the vertical panels hold the hardware and boning. Floating liner inside, and 6 garter tabs.
Binding Black leather; folded under on the front and then clipped short on the underside – common in leather or vinyl binding to minimize bulk.
Waist tape None –  typical of a ribbon-style corset. Ms Martha says her corsets are not for tightlacing.
Modesty panel MASSIVE 10-inch wide back panel that has a single bone running vertically down the center. Leather on the outside and twill on the inside. Also has a 2″ wide leather placket in front.
Busk 11-inch long, heavy duty busk – one inch wide on each side. Quite a bit stiffer than the standard flexible busk.
Boning Total of 8 bones in this corset. 2 spirals on each side seam and 2 spring steels sandwiching each line of grommets in the back.
Grommets 24, 2-part size #0 grommets. These grommets and the washers both have a very large lip which I like. The inside of the grommets have a few very tiny splits, but it’s forgivable because it doesn’t catch on the laces.
Laces Flat braided nylon shoelace style in black; they have a little bit of spring to them. Bulky, so they don’t glide through the grommets quite as well as a thinner one would, but it’s still very strong and very difficult to break.
Price Currently $175 USD in leather, and $170 in silk.

Final Thoughts

This cincher has a beautiful shape – I think it’s one of my favorite shapes of my underbust collection. It is totally comfortable over my hips and feels very secure but not overbearingly tight around my ribs. Because this is made out of leather and twill, I feel that it has stretched out a bit, but not dramatically. Note that the leather did have a strong scent to it when I first opened the package, but I left the corset to air out for a few days in a ventilated room and the smell soon dissipated. Later on I did change out the laces – while the original ones were very strong, it was also quite thick so I experienced a lot of friction when trying to tighten the corset, making it difficult to put on and take off so I simply changed them with thinner shoelaces. But I still own and wear this corset quite often, a year later – you can see it in some of my later videos, like this dressing with your corset post.

Now, be aware that I don’t know what will happen with your corset if you tightlace in this – mine has seemed to hold up fine – but there might be a possibility of a busk pin popping or a seam coming loose, if Ms Martha doesn’t give guarantees that her corsets stand up to tightlacing. I’m just putting that out there.

One thing I want to touch on is the sizing. These corsets run small. When I was looking at the size chart, a Small was recommended for natural waist sizes 20″ – 28″. Since my waist was around 27″ at the time that I ordered, I thought a Small would be great. Ms Martha strongly recommended that I go with a Medium instead. Apparently the size Small has a miniscule waist of only 18″ which was been far too small for me! I later heeded her advice and she was very kind and patient with me about exchanging this cincher. A size Medium has a closed waist of 22″.  So if you are petite or if you are around my size, consider ordering a size up. If you’re naturally on the fluffier side, then you will probably be able to reduce more than me, so order true. This store has the largest range of sizes of any off-the-rack store I’ve found to date, offering corsets for people with waist sizes 18″ up to 52″.

So for your consideration, here is Ms Martha’s size chart that has the “closed waist” corset sizes:

Small Medium Large XL 2XL 3XL 4XL
 18″  22″  26″  30″  34″  38″  42″
Posted on Leave a comment

Axfords C242 Lace Underbust Corset Review

This entry is a summary of the review video “Axfords C242 Corset Review” which you can watch on YouTube here:

Fit, length Circumferential measurements are very comfortable; no pinching in the hips or ribcage. Much curvier than I was expecting. This is a longline corset, starting lower on the ribcage and ending low on the hips – center front is 11″.
Material 3 layers: the strength layer is the inside lining – a tightly-weaved white cotton coutil (made especially for Axfords). Coral satin fashion fabric is flatlined to the coutil, and then the white real lace is laid ontop of the satin.
Construction The seams are top-stitched; bones are in internal boning channels at the seams made from twill or Prussian tape.
Binding Satin on one side and grosgrain ribbon on the other side. Quite unique from commercial bias binding used in other corsets. Neatly machine stitched on both sides.
Waist tape None.
Modesty panel Attached 6″ wide protector, not boned but it is stiffened, so it’s flexible but stands on its own. When I’m lacing down it doesn’t need to be adjusted, and it curves nicely with the contours of my spine. Very comfortable. Has a placket overtop of the busk to hide the hardwear.
Busk Heavy busk, 10″ long and one inch wide on each side. Quite a bit stiffer than the standard flexible busk.
Boning 14 bones total. There are 10 hefty spiral bones – they’re 7mm wide instead of 5mm wide. Also four ¼ inch wide spring steel bones which are also very sturdy and quite thick.
Grommets 30 grommets total, size #00 two-part grommets with moderate flange; set equidistantly. Axfords says that they use smaller grommets set closer together for more controlled tightening of the corset. Some splits along the back of the grommets but they do not catch on the laces and are not pulling out.
Laces Strong tightly woven braided shoe-lace style laces; they’re thin, they grip well and they are very long. No stretch or spring to the lace.
Price Currently £125 ($195 USD) for the lace overlay style, but £115 ($180 USD) without the lace.

Final Thoughts:

This corset is adorable, feminine, pretty, shapely… I think this is the girliest underbust I own – pink with floral lace. I’m impressed at how smoothly the delicate lace lays (say that five times fast!) over the pink satin – do I detect some roll-pinning? ;) Even when worn at large reductions, the lace does not pull away from the seams or wrinkle up with stress.

I was initially concerned about the strength fabric as it was said to be coutil but didn’t have a herringbone weave – this was my first experience with a plain-weave coutil – yet it has stood up the test of time, even without a waist tape. The grommets are also still holding up well several months later – I find my preferences now leaning towards more and smaller grommets on my lacing panel as it’s easier to make fine adjustments when lacing up.

The fit of this corset is flattering as well (in my opinion); I like the conical ribcage, and the hip gores make this longline corset very  comfortable over my hips. The shape is quite similar to the Mae Extreme corset by What Katie Did – I am able to cinch down further in this corset than I was able to in the regular Mae.

All of Axfords’ corsets come with a complimentary storage bag as well – of course, don’t buy a corset just for the bag, but only if you think the corset is as lovely as I think it is. You can see this corset in other colors, and other corset styles on their website here.

Posted on Leave a comment

Axfords C112 Lace Overbust Corset Review

This entry is a summary of the review video “Axfords C112 Corset Review” which you can watch on YouTube here:

Fit, length Circumferential measurements are very comfortable; no pinching in the hips or ribcage. Much curvier than I was expecting. Not a longline corset; comes to my upper hips. It’s advertised as an overbust corset but it is closer to a demibust corset on me – center front is 12½”, while highest part is about 13″.
Material 3 layers: the strength layer is the inside lining – a tightly-weaved black cotton coutil (made especially for Axfords). Satin fashion fabric is flatlined to the coutil, and then the real lace is laid overtop of the satin.
Construction The seams are top-stitched; bones are in internal boning channels at the seams made from twill or Prussian tape.
Binding Satin on one side and grosgrain ribbon on the other side. Quite unique from commercial bias binding used in other corsets. Neatly machine stitched on both sides.
Waist tape None.
Modesty panel Attached 6″ wide protector, not boned but it is stiffened, so it’s flexible but stands on its own. When I’m lacing down it doesn’t need to be adjusted, and it curves nicely with the contours of my spine. Very comfortable.
Busk Heavy busk, 12″ long and one inch wide on each side. Quite a bit stiffer than the standard flexible busk.
Boning 14 bones total. There are 10 hefty spiral bones – they’re 7mm wide instead of 5mm wide. Also four ¼ inch wide spring steel bones which are also very sturdy and quite thick.
Grommets 32 grommets total, size #00 two-part grommets with moderate flange; set equidistantly. Axfords says that they use smaller grommets set closer together for more controlled tightening of the corset. Some splits along the back of the grommets but they do not catch on the laces and are not pulling out.
Laces Strong tightly woven braided shoe-lace style laces; they’re thin, they grip well and they are very long. No stretch or spring to the lace.
Price Currently £135 ($213 USD) for the lace overlay style, but £125 ($197 USD) without the lace.

Final Thoughts:

The red satin with floral lace is a beautiful combination (apparently I’m guilty of requesting that combination on another corset as well). I’m impressed at how smoothly the delicate lace lays over the red satin – do I detect some roll-pinning? ;) Even when the back is completely closed, don’t seem to be tension lines and the lace is not coming away from the stitching.

I was initially concerned about the strength fabric as it was said to be coutil but didn’t have a herringbone weave – this was my first experience with a plain-weave coutil – yet it has stood up the test of time, even without a waist tape. The grommets are also still holding up well several months later – I find my preferences now leaning towards more and smaller grommets on my lacing panel as it’s easier to make fine adjustments when lacing up.

As for the fit of this corset, it’s indeed very curvy – I didn’t feel any pinching on my hips or much compression at the bust. It’s rare for me to be able to close an overbust corset all the way comfortably, but it was no problem with this one. Unfortunately, because of my long torso and the extremely gentle sweetheart shape of the corset, this is more of a demibust than an overbust on me. I would never be able to wear this without something underneath if I want to keep myself decent. This corset looked amazing on my more petite sister and I ended up gifting it to her, so this corset has certainly not gone to waste.

All Axfords corsets also come with a complimentary storage bag; an offer I have never seen with any other company. The bags are large enough to hold two corsets, so they have come in quite handy in keeping my corsets safe and pristine. You can see this corset and other styles at the Axfords website here.

Posted on 1 Comment

Azrael’s Accomplice (AZAC) “Curvy Girl” Corset Review

This entry is a summary of the review video “AZAC Curvy Girl Corset Review & Modification” which you can watch on YouTube here:

Fit, length Curvy, extreme hourglass silhouette. Slightly longline over the hips. Waist stretched over time (about 1.25 inches).The longest part of the corset at the center front is 12.5”. Good for people with an average-length torso. Has enough room in the ribcage and hip areas; very comfortable. May accentuate lower tummy pooch due to inward bend at the front waist.
Material Mostly 3 layers. The fashion fabric is a lightweight hot pink satin (it’s available in other colours), and is flatlined to a light woven cotton underneath. The strength layer of the corset is the twill lining.
Construction 5 panel pattern with 1 large hip gore per side. Top-stitching between panels. It looks like external boning channels but these are simply decorative and only sewed to the top pink satin; the boning is inserted into channels created between the twill lining and strips of canvas laid down inside.
Binding Baby pink satin bias binding around the hip gores and around the top and bottom match the decorative channels, and are machine finished on the inside and outside.
Waist tape 0.5″ wide invisible waist tape between the interlining and lining.
Modesty panel Single layer, unboned modesty panel in the back made from the same hot pink satin. There’s also an unstiffened modesty placket in the front under the busk.
Busk Standard flexible busk (1/2″ wide on each side), 11″ long with 5 pins. Busk is reinforced by a ¼” flat bone on each side.
Boning 14 steel bones not including busk, all ¼” wide flat steel. They’re finished nicely, but they are extremely flexible. This is alright where it curves over the extreme hip spring, but the bones don’t feel sturdy in the back by the grommets (tends to bow outward at the waist).
Grommets 20 grommets total; 2-part (includes washer) and in size #0. I think it could have used about 4 more grommets near the bottom, which I put in later. Grommets are sturdy with a large flange, there is no fraying around the material, they’re not pulling out, although the ribbon catches a tiny bit on a couple of the split grommets in the back while I’m tying it up.
Laces Half-inch wide double-faced satin ribbon that matches the decorative binding and channels. Very strong, hasn’t frayed much even with the slight catching on the grommets.
Price Currently $165 USD

Final Thoughts:

Don’t get me wrong, I adored the shape of this corset. It was indeed a corset for curvy girls! I was just torn on how light it was. Anyone who has handled a few real corsets can know how deceptively heavy a corset can be, but this one was as light as, say, a t-shirt. I loved it because it didn’t feel like a burden to wear, but was slightly concerned that it might not have been steel boned.

I decided to do a little dissecting (nothing that I couldn’t repair again) and was relieved to find that it did indeed have flexible flat steel bones. For good measure and ease of lacing, I replaced just the bones in the grommet panel, and also added a few more grommets. I also boned and suspended the modesty panel, although that has no real bearing on the corset itself. The rest of the corset – quality of the grommets, twill strength layer, internal waist tape etc – are of typical off-the-rack quality, which I was satisfied with.

To see the Curvy Girl corset and other styles made by Azrael’s Accomplice, you can find their site here.