This entry is a summary of the review video “Grey & Green underbust case study”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:
Self-drafted, longline (low over the hips) underbust corset with a peaked front top and a straight bottom edge. Made to close at 22″ at the waist. I took 5 horizontal measurements and 9 vertical measurements to draft this.
Fashion fabric is a black/white fine herringbone weave with metallic gold thread pinstripes This was fused to herringbone coutil interlining and lined in fern green satin.
Drafted from a 6-panel pattern and both topstitched and lockstitched for extra strength. Boning channels are external (made from green satin fused to coutil) and the lining floats.
The binding at top and bottom are made from 2-inch-wide strips of green satin, machine stitched on both sides.
1-inch wide waist tape, invisibly stitched between the coutil and the lining.
Suspended modesty panel stiffened with plastic canvas and finished the same way as the corset – covered in the pinstripe fabric and bound with green satin on top and bottom.
Heavy duty stainless steel busk (1″ wide on each side) and was cut to 13″ long, with 5 pins.
20 bones not including the busk; I had used 1/4″ wide spirals double-boned at each seam (except the one adjacent to the busk) in the external channels. By the grommets there’s a 1/2″ wide flat bone on the outer edges and 1/4″ wide flat bone on the inner side.
There are 32, 2-part size #0 grommets (16 on each side), finished in silver (Chelsea’s choice). The grommets have a large lip around and are spaced 3/4″ inch apart down the length.
Flat nylon braided shoelace-style laces; 8 yards long. They grip well, are densely woven and are resistant to catching, fraying or snapping.
The retail price for something similar is around $280 (underbust corset + heavy busk upgrade + double boning upgrade + external boning channels upgrade).
This entry is a summary of the review video “Longline Overbust Review (CorsetDeal/Corsets-UK)”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:
Gently curved, gives a slim silhouette without a lot of cinch. The center front is 15.5”. The longest part of the corset at the apex of the bust is 18”. Sweetheart neckline. Longline corset, ending low over the hips.
Two layers; the outside heavy polyester pinstripe fabric, and the inside cotton twill.
6 panel pattern. Panels are top-stitched at the seams, and then internal boning channels laid down, made of black twill.
The binding at top and bottom are black polyester bias tape. Also has 6 garter tabs
Waist tape running through the corset, seen on the inside, made of 1” wide single-faced satin ribbon.
Unboned modesty panel, 8 inches wide made from polyester pinstripe on the outside and black twill on the underside. No placket beneath the busk.
Slightly heavy duty, almost 1″ on each side. Stiffer than a standard flexible busk. 14″ long with 6 pins.
14 steel bones in this corset not including the busk. Single boned on the seams. The two bones that curve over the bust are made of spiral steel; all the other bones in this corset are spring steel.
There are 32, 2-part size #0 grommets (16 on each side), finished in nickel. The grommets are sturdy with moderate size lip around, there is absolutely no fraying around the material, they’re not pulling out.
Black flat nylon braided shoe-lace style. Very strong, grips fairly well. It has a little bit of spring. They are resistant to fraying and catching.
Currently ranges from $40 USD – 85 USD (£25 to £54 in UK).
After experiencing the unflattering way the shorter Corsetdeal overbusts barely covered my girls, I opted for a longline style instead. This was a slightly better fit. I definitely felt that my bust was more secure, and the position of the waist tape was in a more reasonable place, although still not right at my waistline (it was sitting perhaps an inch above my natural waist).
The pattern for the overbust corsets have the same bust/waist/hip circumference as the pattern for the regular overbusts, so keep this in mind. It’s as if they took the original pattern and simply stretched it out vertically to elongate it (i.e. what they did not do, was theoretically take the original pattern and extrapolate the lines to longer [and wider] top and bottom edges). I hope at explanation made sense – if not I will draw a diagram for you all. How this translated to fit on me, is that it fixed the flaring issues that I had at the hips in my shorter overbust corsets, but it resulted in the appearance of a less curvy corset overall. Therefore I recommend this corset to buyers who are tall/ have a long torso, and are either slim/ruler shaped, or slightly apple shaped. If you are a pear or natural hourglass shape, there is a possibility that this corset may not be curvy enough for you.
I didn’t have any problems on my hipbones here in terms of the pattern itself, although the placement of the internal bones at the side seams was unfortunate, as the rigid spring steel bones sat right over a nerve on my iliac crest, causing some chafing and discomfort. The problem was partially resolved by simply replacing the flat bones on the sides with more flexible spiral steel boning, which was a surprisingly easy operation.