Posted on Leave a comment

Vanyanis “Ruby” Corset Review

This entry is a summary of the Vanyanis “Ruby” Corset Review video. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

 

Fit, length Center front is 12 inches long, the princess seam is 8.5 inches (4 inches above the waist, 4.5 inches below the waist), the side seam is 9.5 inches and the center back is 11 inches long.
Circumferential measurements: underbust is 28″ (rib spring is 6″), waist is 22″, and hip is 34″ (hip spring is 12″). The ribcage is very conical, and the hips are gently cupped.
Material 3 main layers: the fashion is red satin with black lace overlay. The strength fabric is herringbone coutil, and the floating lining is a soft black cotton.
Construction 7-panel pattern (14 panels total). Panel 4 is designed to curve over the hip so there is no true “side seam”. Construction: satin was flatlined to coutil, and panels assembled with the seam allowances facing inward (added topstitch for reinforcement; each seam was stitched at least 4 times for extra strength). Internal bone casings laid down, and covered by a floating lining.
Waist tape 2 cm wide (slightly less than an inch) cotton waist tape, secured “invisibly” between the layers of fabric.
Binding Made from strips of black duchess silk, machine stitched on outside and inside. Stitched in the ditch on the outside and tiny topstitch on the inside.
Modesty panel Awesome modesty panel in back – 4.75″ wide, finished in matching red satin / black lace overlay on outside, and cotton inside. Quilted and boned with 2 horizontal and 2 vertical bones, and comes with snaps to easily suspend the panel on the laces, or remove the panel when desired.
In the front there is a modesty placket, extending about 1/2″ out from the knob side of the busk, covered matching red satin with black lace.
Busk 11” long, with 5 loops and pins, the bottom two a little closer together. Wissner brand, standard flexible busk (1/2″ on each side) and a bit flexible, but there are added flat steels adjacent to the busk to add stiffness. The busk is also covered in a matte black powder coating.
Boning 30 bones total in this corset, 15 on each side. Single boned on the seams and additional bones in the middle of each panel, with ¼ inch wide spirals. The bones sandwiching the grommets are flat steel, and more flexible than usual, so it could curve to the lumbar spine. There are 4 flat steels by the busk (2 on each side).
Grommets There are 24, two-part size #0 grommets (12 on each side). They have a small-to-medium flange and are spaced equidistantly, and finished in gunmetal grey or pewter. No splits on the underside.
Laces Black 1/2″ wide double-faced satin ribbon (glides well through the grommets, holds knots and bows securely, long enough). Finished with nice metal aglets.
Price Available in sizes 20″ up to 30″.
Price is $795 AUD (converts to about $635 USD).
VIP mailing list members get $100 AUD coupon, which brings the price down to $695 AUD (about $550 USD).


Final Thoughts:

Vanyanis is a couture brand based in Australia, run by Lowana O’Shea.

This corset is the best quality OTR piece I’ve ever seen. Made with herringbone coutil, expertly-matched fine lace, black hardware, evenly distributed steels, and an insanely comfortable pattern, Vanyanis has set a new bar for factory-produced corsetry.

For the pattern of this corset, I believe Lowana mentioned that this started out as the same dimensions and silhouette as her “Alecto” corset (a standard size, made-to-order Vanyanis product made by Lowana herself, introduced back in 2014) – however, the “Ruby” Corset was cut to have points on the top and bottom edges and to ride a bit higher over the hip. The “Lilian” corset is a grey / silver satin, and cut more straight across the top and bottom edges, but still the same general pattern.

And of course, the “Ruby” and “Lilian” corsets were made in a factory under Lowana’s supervision, which is why she describes these as an “off the rack” collection as opposed to the usual “ready to wear”.

One of the best features about this corset is the painstakingly pattern-matched lace in this corset. Because the lace had to be cut to each panel and flatlined (as opposed to pieces overlaid when the whole corset was finished being assembled), Lowana says that there was quite a lot of time and care (and stress) put into this step at the factory, and quite a lot of fabric wastage as well as they had to think about having sufficient seam allowance on each piece. This drove up the price of the corset – but it has a truly stunning final effect.

Lowana says that this corset is definitely strong enough for waist training, but due to the delicate nature of the lace overlay, it might become “roughed up” over time, so do keep in mind that the more you wear this piece, the more worn it will look.

This is Lowana’s first OTR line and as such it’s a small run to start (only 25 of the Ruby and 25 of the Lilian corsets in all sizes). If these sell well, Lowana is interested in making more colors, styles, and perhaps extended sizes as well.

If you’d like to see my interview with Lowana of Vanyanis, click here. And if you’d like to visit her Vanyanis shop, click here.

Posted on 1 Comment

C&S Constructions Double Corset Review

This entry is a summary of the review video “Rainbow Holow Corset! Two C&S Constructions Corsets (Review / Study)” which you can watch on YouTube here:

Rainbow Holo Corset

Fit, length Center front is 10.5 inches long, princess seam is 9,5 inches, side seam is 9.5 inches and center back is 11.5 inches.
Underbust 29″, waist 21″, high hip 34″.
Rounded ribcage and rounded hips. The busk is flexible and allows inward bowing.
Material 2 main layers: fashion layer is holographic silver foil (almost like interwoven tinsel). Lined in herringbone coutil.
Construction 4 panel pattern! (Surprising as it’s so curvy.) Layers were flatlined, panels were assembled and reinforced with sturdy topstitch (seam allowances facing outside). External boning channels laid down over the seams.
Waist tape 1-inch-wide waist tape “invisibly” installed between the layers, full width.
Binding Bias strips of matching holographic foil material, machine stitched on both inside and outside (zigzag stitch; the foil material likes to shred/fray).
Modesty panel None (this is a sample). However on the C&S website, they say that all corset commissions come with a back modesty panel.
This corset sample does have a wide boned underbusk, covered in black herringbone coutil.
Busk 9″ long, with 5 loops and pins, equidistantly spaced. Standard flexible busk (1/2″ wide on each side). The boned underbusk gives a bit more stiffness, but the corset still “dishes” on my body (this may be deliberate – common of C&S corsets, and this also seems to help me achieve a higher comfortable waist reduction in this corset).
Boning 11 steel bones, not including busk. 5 on each side, plus boned underbusk in front. On each side, 3 spirals single boned on the seams, and 2 flats (1/4″ wide) sandwiching the grommets.
Grommets 30 grommets total, size #00 two-part grommets with small flange; spaced a little closer together at the waistline for easier lacing up. Underneath the grommets there are wider washers that act as a wider flange – they may help protect them from pulling out, they give more thickness for the grommet to “bite down” on (preventing wiggling or looseness, and they also hide any fraying or splitting of the outer holographic material. There are no splits in these. No wear/fraying/pulling out of grommets.
Laces 3mm wide satin rattail cord. They have zero stretch, they glide well through the grommets (slippery), and they are long enough.

 

Purple with Lace Longline Corset

Fit, length Center front is 12.4 inches long, princess seam is 11 inches, side seam is 11.5 inches and center back is 13 inches.
Circumferential measurements: Underbust 28″, waist 20″, high hip 35″.
Conical ribcage. Slight hip shelf, and longline corset. Also bows at the front (likely a deliberate effect to get more of a waist reduction).
Material 3 main layers: fashion fabric is Cadbury purple satin (may be a satin coutil, or fused to a strength fabric), overlaid with black lace. Lined in black cotton drill.
Construction 4 panel pattern! (Surprising as it’s so curvy.) Layers were flatlined, panels were assembled and reinforced with sturdy topstitch (seam allowances facing outside). Black external boning channels laid down over the seams, plus extra bones in the middle of the panels (sandwiched between the layers).
Waist tape 1-inch-wide waist tape “invisibly” installed between the layers, full width.
Binding Black satin ribbon (the same ribbon used for external boning channels), matchine stitched on both sides using a zigzag stitch.
Modesty panel None (this is a sample). However on the C&S website, they say that all corset commissions come with a back modesty panel.
This corset sample does have a wide boned underbusk, covered in black satin coutil.
Busk 11″ long, with 5 loops and pins, equidistantly spaced. Standard flexible busk (1/2″ wide on each side). The boned underbusk gives a bit more stiffness, but the corset still “dishes” on my body (this may be deliberate – common of C&S corsets, and this also seems to help me achieve a higher comfortable waist reduction in this corset).
Boning 17 steel bones, not including busk. 8 on each side, plus boned underbusk in front. On each side, 3 spirals single boned on the seams, and an additional 3 bones in the middle of the panels. Also on each side there are 2 flats (1/4″ wide) sandwiching the grommets.
Grommets 34 grommets total, size #x00 two-part eyelets with tiny flange; set closer at the waistline to make lacing up easier. On the underside, the eyelets were perforated (petals splayed out) but they don’t catch on the laces. There are still very large washers on the underside to prevent the eyelets from pulling out.
Laces 1/8″ wide flat black cotton shoelace. They have zero stretch or springiness, they glide well through the grommets, they hold knots and bows securely, and they are long enough.

 

C&S Model Karen models the same holographic corset – see this and other pictures on C&S Constructions website, in Gallery 1!

Final Thoughts:

Both of these corsets were made for one of C&S Constructions’ previous models, who had a slightly smaller ribcage and slightly fuller hips than me – so these weren’t made to measure for my body, but we’re “close enough” to be able to fit the same corsets similarly.

I adore the holo corset especially, and it’s a very thin and lightweight corset. Even though both corsets are a smaller waist than I’m accustomed to wearing these days (I prefer to stay at 22 inches, but the holo corset is 21″ and the purple corset is 20″), I’m able to achieve slightly more of a waist reduction in both of these because of the comfortable patterning, and also likely because of the slight “dishing” or bowing in the center front busk.

In both corsets, the construction is a bit more “rugged” than I’m accustomed to seeing these days. The overlocking / zigzag stitching is visible (especially on the inside of the corset). I thought this might have just been because these were sample corsets for photoshoots, but from other C&S customers I’ve spoken with, it seems that this was just the way many corsets were constructed in the 90s and early 2000s. While they’re just not as “tidy” in their finish compared to most corsets on the market today, these corsets have held up well over the years and give a beautiful silhouette, and are a reflection of C&S’s good reputation. Visit C&S Constructions website here.

Do you own this corset or another piece from C&S Constructions? Let us know what you think of it in a comment below!

Posted on Leave a comment

Morgana Femme Couture MF1303 Gold Satin with Black Lace Longline Underbust Review (MFC)

This entry is a summary of the review video “Morgana Femme Couture Lace Overlay Longline Underbust Corset (MF1303) Review” which you can watch on YouTube here:

 

Fit, length Center front is 14 inches long, princess seam is 12 inches (5.5″ above the waist, 6.5″ below the waist), side seam is 13 inches and center back is 14 inches.
Underbust 27″, waist 22″, low hip 36″.
Traditional hourglass silhouette with conical ribcage. Longline corset, recommended for tall or long-waisted people. Will hold in lower tummy pooch, recommended for pear-shaped people.
Material 3 layers; fashion layer is gold satin, with black lace overlay. The interlining (strength fabric) is 100% English cotton coutil, lining of cotton twill. Boning channels are satin coutil.
Construction 6 panel pattern. The strength fabric, satin and lace were all flatlined and panels assembled, and external boning channels strengthen seams. Floating lining.
Waist tape 1″ wide waist tape, secured “invisibly” between the layers, secured down at boning channels. Full width (center front to center back).
Binding Black satin coutil bias tape neatly machine stitched on both inside and outside with a small topstitch (may have been stitched in one pass, using a special attachment). No garter tabs.
Modesty panel By default, MFC corsets don’t come with a modesty panel in back. In the front there’s an unboned placket, about ¼ inch wide, finished in black satin coutil, extending out from under knob side of the busk.
Busk 12.5″ long, with 6 loops and pins (the last two a bit closer together). Standard flexible busk (1/2″ wide on each side) of average stiffness, and reinforced with backed with a ¼” wide flat bone on each side. See Final Thoughts for how it was covered.
Boning 24 steel bones not including busk. On each side, 9 spirals (1/4″ wide) are single boned on the seam (and also in the middle of the panels) in external channels, 2 flats (1/4″ wide) sandwiching the grommets and an additional flat steel by the busk.
Grommets 26 grommets total, size #0 two-part grommets with moderate flange; set a bit closer together at the waistline, the occasional split, no wear/fraying/pulling out of grommets.
Laces Strong 1/8″ wide cotton flat shoe-lace style laces; they have zero stretch, they hold the bows and knots well, and they are long enough.
Price Available in waist sizes 18″ up to 26″. Currently $300 USD on their Etsy store (standard size, ready-to-wear) or $290-$350 USD on the MFC website (made-to-measure and custom colours, price depends on the size).

 

Additional Thoughts:

Morgana Femme Couture MC1303 longline corset, with satin and lace overlay. Photo courtesy of Awin / Etsy.

I purchased this corset from a friend (Jasmine Ines of Sin & Satin) and I believe I’m the third owner – so this corset has held up extremely well considering how old it is and how much it’s been worn. However, it was not made for my body – it was made-to-measure for the first customer, who has a much smaller ribcage and much fuller hips than I have, as well as someone with a much longer torso from the waist down compared to me.

As per usual, I’m quite impressed by the quality of the materials in this corset. The gold satin and black lace overlay feels lush (and if you dislike the gold, you can have the corset made in nearly any other color of satin you like), English herringbone coutil strength layer, satin coutil boning channels and cotton lining. Once you go quality, you won’t want to go back.

Another rare feature of MFC corsets is their “skinny panel” over the busk – on the loop side, it’s often one continuous piece of fabric that wraps around the busk, with buttonholes for the loops to peek through. This prevents any possibility of the center front seam ripping open. I’m on the fence as to whether I like the look of buttonholes, as it can make the busk look a bit “hairy” compared to a clean seam, but I can’t deny that it is strong construction.

The only thing I would improve upon in this corset is I wish they were available in a wider range of sizes! There are so many full figured women who would love to own an MFC corset, it would be great if MFC could eventually expand their most popular corsets up into the 30+ waist range – at least for made-to-order corsets.

See Morgana Femme Couture’s MF1303 corset here, or visit their Etsy shop here.

Do you own this corset or another piece from Morgana Femme Couture? Let us know what you think of it in a comment below!

Posted on 2 Comments

Dark Garden Corselette Review

This post is a summary of the “Dark Garden Corselette Review” video, which you can watch on Youtube if you prefer:

 

Fit, length Center front is 11 inches long, the shortest part of the corset at the side seam is 5.5 inches (cut very high over the hip), and the enter back is also 8.5 inches. Circumferential measurements: waist is 22″, ribcage 26″ (measured about 3 inches above the waist), high hip 28″ (measured about 2.5 inches below the waist). The silhouette is quite dramatic; I consider this a wasp waist. Side bones are pre-bent to give a nipped-in waist.
Material Fashion fabric is red poplin, with a black lace overlay (every panel is mirror-matched), and the strength fabric (lining) is densely-woven black canvas.
Construction 4 panel pattern. It seems as though all layers were flatlined for each panel, panels were assembled with seam allowances facing outward, and these seams were then covered with external boning channels (2 bones per seam).
Binding Black satin bias binding, machine stitched on both sides, with a slight topstitch visible on the outside. 6 garter tabs.
Waist tape 0.75 inch wide twill waist tape, exposed on the lining side of the corset. It starts at the seam between panels 1-2, and ends at the center back seam.
Modesty panel Modesty panel is around 5″ wide, finished in the same fashion fabric (red poplin with black lace) and black canvas lining. Stiffened with 4 steel bones and left separate to slip under the laces when worn (or you can choose to not wear the modesty panel). There is a teensy seam in the center front which is not a modesty placket per se, but it does help prevent a visible gap between the busk.
Busk 10 inches long with 5 pins, equidistantly spaced. Standard flexible busk (half inch on each side). There is also a 1/2″ wide flat steel on either side of the busk for reinforcement. In the pointed cinchers, the busk seems to be shaved down on an angle so the tips follow the same line as the fabric!
Boning 18 total bones not including busk. 1/4″ wide bones, double boned on the seams. The side seams must be flat steel since they are pre-bent. Two further 1/4″ wide flats sandwich the grommets on each side, as well as one 1/2″ flat steel by the busk, making a total of 9 bones on each side.
Grommets 20 grommets total, size #00 with medium flange, finished in black and set equidistantly. A few splits on the underside, but for the most part they’ve rolled nicely and don’t catch on the laces. Washers are large to prevent the grommets from falling out.
Laces 3/8″ black double faced satin ribbon. Zero spring. They glide well through the laces.
Price Available from sizes 18-38, and at the time that I’m writing this review, the corselette costs $315 for plain black poplin, and $395 if you want an identical style to this (with coloured poplin and mirror-matched lace overlay).
Dark Garden Corselette, modelled by Victoria Dagger and photographed by Joel Aron photography

I’m extremely pleased to say that this is the first of four reviews of Dark Garden’s RTW (ready-to-wear) corset selection, including the Cincher, the classic Valentine and the Risqué Valentine

The Corselette is one of the shortest corsets I’ve ever tried, with a side length of only 5.5 inches which may fit even the shortest of waists. This particular style is pointed in the front with a 10 inch busk; but if you don’t like pointed corsets or you prefer something that is more conducive to hiding under clothing, you can request that the Corselette be made with a more rounded center front instead (the center front may be slightly shorter in this case). If you think you need more control around the sides and back to control flesh spillover, or if you want your lower tummy pulled flat, I would suggest trying one of their slightly longer underbust corsets.

I love how they used flat steel bones along the side seams that had been pre-curved to nip in the waist and kick out the hip, making a very curvy and comfortable corset from the first time I wore it – no numbness around the hips.

But one of the things I appreciate most about Dark Garden is their ethics. Every one of their corsets are made from start to finish in the US and they take enormous pride in their construction, which is evident in the pattern matching in their lace or brocade corsets for a luxurious final effect.

The Corselette can be viewed on Dark Garden’s website HERE.

Posted on 1 Comment

Boom! Boom! Baby! Boutique Lace Overbust Corset Review

This entry is a summary of the review video “Boom! Boom! Baby! Boutique Corset Review” which you can watch on YouTube here:

Fit, length Front is about 14 inches long, from peak of bust to bottom (at longest part) is 15.5 inches. Very gentle hourglass shape. Bottom edge is a rounded shape so the corset stops just at the iliac crest (upper hips). Sweetheart bust, and plenty of room in the high back to prevent muffin top. Quite comfortable on me – very curvaceous shapes may want to invest in the upgrade for made-to-measure.
Material Fashion layer is silver/ pewter satin with black lace overlay; backed onto a sturdy strength layer underneath; lining is cotton coutil.
Construction 5 panel pattern. Top-stitching between the panels, single-boned on the seams, and a floating coutil liner (very comfortable). No garter tabs.
Binding Standard black satin bias tape, machine stitched inside and outside.
Waist tape 1″ wide invisible waist tape between the interlining and lining.
Modesty panel Matching 5″ wide modesty panel, made from the same coutil/satin/lace overlay, and also bound in black bias tape. Attached to one side of the corset; removable if desired.
Busk Heavy-duty wide busk (1″ wide on each side) about 13″ long (6 pins).
Boning 12 steel bones not including busk. On each side, there are 4 spiral bones on the seams and another two steel flats sandwiching the grommets at the back.
Grommets 30 grommets total, size #00 two-part eyelets (Prym brand) with moderate flange; set equidistantly; high quality – few splits, no wear/fraying/pulling out of grommets.
Laces Strong cotton braided shoe-lace style laces; they’re thin, they grip well and they are long enough. Very easy to lace up. Zero spring.
Price This particular piece was a one-off (sample) but Kirsteen does take special orders outside of what is available in her store. Most of her corsets on Etsy, made to standard sizes, are advertised as around or under £150, and these corsets can be made to custom measurements for an additional £50. You can see the options on her website here.

Final Thoughts:

This piece is absolutely beautiful. I had seen Kirsteen’s work around the internet for awhile, but I first learned of the name “Boom! Boom! Baby! Boutique” when it was featured in the Lingerie Stylist’s “Top 10 Corsetieres” article in late 2012. Finally had the name of the designer of these fun, circus- and military-themed corsets. Checking out her Facebook page, I stumbled upon an auction of her pieces, and I instantly fell in love with this floral and lace number – not because it was rather different from the pieces normally available in her store, but because it was elegant in and of itself; simply put. I hadn’t yet owned a piece embellished in this way. The fact that it was one-of-a-kind made it that much more special!

I was not disappointed in Kirsteen’s workmanship at all – the stitchwork is neat, the lace overlay doesn’t wrinkle in the slightest, the beaded lace trim and roses are secured with care and attention, the coutil lining inside is high quality, smooth and comfortable. For a piece that was not intended for my measurements, it fits surprisingly well (I feel so fortunate to have these body dimensions). Do not be surprised if you see me review her work again in the future. In fact, I might almost guarantee it. ;)

To see the other styles available by Boom! Boom! Baby! Boutique, visit Kirsteen’s Etsy shop here!