Tag Archive: full bust

Corset and Strapless Bra: low-back solution for fuller busts!

In Summer of 2014, I purchased this lovely dress from Zumel & Co in Toronto. Although I love the dress, it has a bit of a low back (enough that my bra band shows in the back). One question I receive quite often, especially from brides, is whether it’s possible to have a low back overbust corset for precisely this reason, and it got me thinking.

This Contessa Gothique corset has a lower back made possible with the help of shoulder straps. Photo: DiaIF. Model: Nea Dune.

This Contessa Gothique corset has a low back made possible with the help of shoulder straps.
Photo: DiaIF. Model: Nea Dune.

If you commission a custom-made overbust, creating a somewhat-low back is theoretically possible (to a point). However, a problem arises especially if you are heavy busted: you’re not going to get the same breast support if you have a very low back. You’ll notice that most overbust corsets don’t have a back that stop close to nipple-height, and not usually lower than under the shoulder blades. This prevents the front of the corset from flopping forward, away from your body. You may be able to adjust that support with halter straps for instance, or even (cringe) heavy duty double sided tape. In any sense, it’s going to be mighty difficult if not impossible to achieve a corseted silhouette with a backless dress.

If there were a cupped overbust corset that allowed you to wear backless, strapless dresses (think Jessica Rabbit) with perfect support, I believe that thousands of people would be all over that! However, in my journey though corsetry, I have never actually found a corset that’s been able to achieve this.

If you want full support along the fullest part of your breasts, you must rely on the fabric wrapping around the entire torso at that same line.
The same premise holds with long line corsets – if you want a lot of control of the lower tummy, you could put many stiff, rigid steel bones in the front, but if you have a protruding lower tummy that resists these bones, the whole bottom front of the corset could end up bowing outwards (especially if the front of the corset extends down into a point and is cut high over the hips). With a longline corset, it helps pull in a lower tummy easily because it has extra fabric that starts at the pubic bone and wraps around the hip area along a similar height, and around to the back.  The tension of the fabric wrapping around the body acts as leverage to help pull that protruding tummy inward.

Seriously, Jessica's dress goes down to the tailbone and has no straps. This defies physics. There has to be skintone mesh, or double sided tape, or something.

Seriously, Jessica’s dress goes down to the tailbone and has no straps. This defies physics. There has to be skintone mesh, or double sided tape, or something.

So, what can be done if you want to wear a low back wedding dress, especially if you’re quite heavy-busted? What I did in the above video was a trick that Ashley (Lisa Freemont Street) taught me a few years back:

Find yourself a well-fitting strapless, longline bra. The Goddess brand strapless low-back bra works great for my purposes, and I love that the lightly boned cups provide support while retaining the roundness of the breast and it gives a slightly vintage shape to my bustline (it doesn’t flatten my bustline like most modern cut strapless bras seem to do). There is a silicone band around the top to help keep it in place on my skin as well.

As it’s a longline bra, it also has a few bones coming down and stopping at around navel height – this helps keep the garment smooth and prevent it from rolling up. If you plan to wear this bra underneath corsets, you can absolutely remove some of the bones in the bra so as not to irritate your skin by having the stays smushed up against your ribs under the corset. I like to wear this bra with an underbust corset (usually a cincher or waspie, which stops lower on the ribcage) worn over the bra – the corset also helps anchor the bra in place so it’s less likely to slide down over the course of the day. Even if I don’t utilize all the hooks and eyes of the bra (you can fold some of the top ones down if you need to accommodate for a lower back), the bra still stays in place due to the silicone strip and the anchoring of my corset.

One thing to look out for, however, is having a bit of “muffin top” with this combination. When you wear very short cinchers or waspies, the more of your ribcage it leaves exposed/ unsupported, the bigger the risk of it giving you “muffin top” (a roll of skin that folds over the top of the corset when worn). The fact that it’s combined with a longline bra in this case does help to somewhat combat this, but how much “muffin” occurs will depend on the person as well (how long your torso is, how low the back of your dress is, and whether your body tends to ‘displace upward’ or ‘displace downward’ in a corset).

The Goddess Longline bra can be partially folded under to accommodate for an even lower back.

The Goddess Longline bra can be partially folded under to accommodate for an even lower back.

There is rhyme and reason to the corset I chose to wear over my longline corset as well! In this video, I’m wearing the True Corset mesh cincher because it’s cut quite straight across at the ribcage and hips – there are no “points” to bow outwards and protrude underneath clothing. As a mesh corset, although it may not last quite as long as other corsets, it makes for more breathable, lightweight undergarments, and therefore a more comfortable experience – especially if you’re planning to wear a warm outfit in a warm venue!

Other inexpensive mesh corsets that hide well under clothing is Orchard Corset’s mesh CS-411 and mesh CS-426 (for those who prefer longline), as well as Madame Sher’s mesh cincher. As much as I adore custom fit corsets, I understand that weddings can be exorbitant. Even the cost of an OTR mesh corset combined with the Goddess bra comes up as cheaper (and quicker to ship) than commissioning a custom overbust corset with a lower back (and, of course, they can be combined with other outfits after the wedding!). Even though a mesh corset may not last a lifetime, it should at least last through your wedding day!

If you have ideas for other corset and bra combinations that work well underneath your low-back outfits, leave a comment down below and help out some other potential brides on a budget!

Corsets Boulevard Global Curvy Overbust Review

This post is a summary of the “Corsets Boulevard Global Corset Overbust review” video, which you can watch on Youtube if you prefer:

Fit, length Center front is 16.5 inches long (due to the tabs that extend down in the front), the princess seam (where you see the highest part of the sweetheart of the bust) is 16 inches long, the side seam is 15.5 inches, and the enter back is shorter at 13 inches. Circumferential measurements: waist is size 24″, full bust is between 34-35 inches, high hip (iliac) is 34-35 inches as well, and the low hip at the lap is about 37 inches in circumference. The silhouette is relatively curvy, definitely a traditional hourglass.
Material Fashion fabric is black satin (but can be specially ordered in any color satin), the strength layer is black twill.
Construction 6 panel pattern (12 panels total). Most of the ease for the bust is in panels 1-2, and most of the ease for the hip is in panels 3-4. The construction is the “welt-seam” method, which is different from a normal topstitch. The corset is double boned on the seams, and sandwiched between the layers.
Binding Commercial strips of 1-inch-wide black satin ribbon (so it wasn’t folded under; the edges of the ribbon were left raw). There are 6 garter tabs.
Waist tape No waist tape (at least, none could be detected when I inspected the corset carefully).
Modesty panel Modesty panel is around 5″ wide (will cover a back gap up to 4 inches wide) and finished in the same black satin as the fashion fabric. It is unstiffened, and stitched to one side of the back of the corset (can be removed if desired). Unstiffened front modesty placket under the busk, again finished in black satin.
Busk 14.5 inches long with 8 loops and pins, equidistantly spaced. Standard flexible busk (half inch on each side).
Boning 24 total bones not including busk. 1/4″ wide spirals, double boned on the seams. Two further 1/4″ wide flats sandwich the grommets on each side, making a total of 12 bones on each side.
Grommets 26 grommets total, size #00 with a small flange and finished in silver. Set equidistantly, about an inch apart.
Laces Black round cord, it is small enough and slick enough to slide through the grommets, but I find that they snag more than flat laces.
Price £55 or around $68 USD
The Curvy overbust as it appears on Corsets Blvd Global's website. Click through to learn more.

The Curvy overbust as it appears on Corsets Blvd Global’s website. Click through to learn more.

This corset is definitely one of the least expensive overbust corsets for curvier wearers, offering a 10-11 inch bust spring, and a 13 inch low hip spring. This brand also offers a large range sizes for this corset, from 18″ up to 40″.

I also appreciate how high the corset comes up over bust, and continues high around the sides to control my “armpit squidge”. In the back it comes down a little lower, but not so low as to accommodate very low-back dresses.

The busk keeps my tummy flat, and doesn’t seem to bow outwards. Having 8 loops and pins, it’s one of the longest corsets I’ve tried to date!

The one feature I wasn’t crazy about are the flaps in the bottom of the center front which are not supported by any steel so they can bend upwards (and therefore don’t offer much in terms of function or support). I believe these to be a nod to the antique Edwardian suspender corsets, but obviously the suspenders/ garters were omitted in this style so the flaps is a bit “vestigial”.

Other overbust corsets of equivalent curve (and support for large cup sizes) tend to average around $300 USD, even for ready-to-wear. Yes, the satin of this piece isn’t quite as lush, and the stitchwork isn’t as pristine as the other brands — don’t expect this piece to live up to the standards as the others — but at its current price, it’s filling a place in the corset industry that other brands aren’t.

I wouldn’t personally waist train in this corset, due to the apparent lack of waist and due to the construction method causing one bone out of each pair being essentially held in by the satin fabric instead of being securely sandwiched into a denser weave cotton (there may be a risk of a steel bone popping through the fabric if this is worn daily for weeks or months). But it would be great for occasional use, special events, and possibly to use as occasional relief from a heavier bust.

On the Corsets Blvd Global site, this curvy overbust in black satin is named the “Keira” corset, and if you get it before February 15, 2016, it will be £55 or around $68 USD currently. Find the corset here.

%d bloggers like this: