Posted on Leave a comment

Orchard Corset CS-511 Mesh Overbust Review

This entry is a summary of the review video “CS-511 Mesh Overbust Review”. If you would like more complete information and side notes about the corset, you can watch the video on YouTube here:

Fit, length Center front is 15.5 inches long, princess seam is 16.5 inches long (10 inches above the waist, 6.5 inches below the waist), the side seam is 14 inches, and the center back is 13 inches long.
Full bust spring is 11″, and lower hip spring is 14″.
The silhouette is hourglass, but the flexible mesh allows for more contouring around curves = giving more of a rounded ribcage, and hips of the corset can contour around your own hips, whether your hips are slanted or shelf-like.
Material Single layer of fishnet style black mesh, and the boning channels / are made with an outside layer of black cotton twill and internal layer of polyester grosgrain ribbon.
Pattern & Construction 6-panel pattern (12 panels total). Panels 1-2 give space for the bust, panels 3-4 curve over the hip. Construction: Panels were assembled and then boning channels sandwiched the seams (on outside and inside), covering and reinforcing the seams.
Waist tape One-inch-wide waist tape made from grosgrain ribbon, sandwiched between the boning channels. Full width (center front to center back).
Binding Made from matching black cotton twill. Machine stitched on both sides, stitched in the ditch (between the corset and the binding) in front, and a necessary top stitch on the underside. 6 garter tabs (3 on each side).
Modesty panel 5” wide and unstiffened, made from 2 layers of cotton twill, and attached to one side of the corset with a line of stitching – this is easily removed, and you can also remove the tags in the back by removing that seam with the modesty panel, in case you find that the tags show through the mesh.
There’s no front modesty placket in this corset.
Busk 14” long, with 6 loops and pins (last two are a bit closer together). Standard width busk (half an inch wide on each side), but Orchard’s busks tend to be more rigid (less bendy) than other busks of the same width.
Boning 14 bones total in this corset. On each side, 7 of them are spirals about ¼” inch wide, in single channels, equidistantly spaced. Then there are two flat steel bones, both ¼” wide, sandwiching the grommets.
Grommets There are 24, two-part size #00 grommets (12 on each side). They have a small-medium flange and are finished in silver. They’re spaced equidistantly about 1” apart.
Laces The laces are ¼” wide flat nylon shoe-lace style. I find them to be long enough, a little springy but it “stretches out” and the springiness dissipates over time. Orchard also sells double-face satin ribbon if you prefer.
Price Available in waist sizes 18″ to 40″, in black and in white mesh.
Sizes 18-32 are $79 USD, and sizes 34-40 are $82 USD, but you can save 10% by using the coupon code CORSETLUCY

 

Brittney from Orchard Corset (the very same I consulted with on sizing) models the mesh CS-511 overbust. Click through to see their selection.

Final Thoughts:

Full disclosure, this corset was sent to me as a sample. I normally take a size 24″ in OTR corsets, but as I’ve been shrinking rapidly this year I requested the size 22″. Brittney from Orchard Corset suggested I go a size down, to 20″ because the mesh has a tendency to expand over time. The thought of wearing a size 20″ in an OTR overbust was a bit mind-boggling, but I hesitantly agreed.

The very first time I put on this corset, I thought it would never fit – but as I wore it in more over the weeks, I did indeed notice that it stretched out, to the point that I can wear it with their recommended 2 inch gap in the back. The hips of this corset are quite large (seemingly much larger or has a higher tendency to stretch compared to the bustline) so I would be more comfortable wearing this corset with a “V” shaped lacing gap, which seems to be par for me with OTR overbusts.

However, this is by far the most affordable mesh overbust currently available on the market, starting at $79. The other mesh overbusts include What Katie Did ($375 USD), and Dark Garden ($895 USD) can be out of many clients’ budget. I can see the mesh CS-511 being used by those who would like some breezy bust support in the heat of the summer, or wearing this corset under strapless dresses (there is a white mesh version as well for summer brides). Because my mesh corset has a few construction imperfections (it’s asymmetric over the hip), I’d be more likely to wear this corset under my clothing as opposed to overtop anyway.

CORRECTION FROM THE VIDEO: Orchard Corset’s mesh underbust corsets usually have bones are evenly distributed around the waist – and the bigger the corset size, the more bones are included – this is still true. However, it seems that this isn’t the case for the mesh overbust corsets (at least, not from what I’ve seen in pictures). It appears that all sizes have the same number of bones, same as with their all-cotton or satin corsets.

Shop for the CS-511 mesh overbust corset from Orchard Corset here, and remember you can save 10% by using the code CORSETLUCY (I don’t get any kickback from this, it’s strictly a coupon/ discount code for you).

Posted on 2 Comments

Orchard Corset CS-511 Overbust Review

This entry is a summary of the review video “Orchard Corset CS-511 Overbust Review”. If you want visual close-ups, you can watch the video on YouTube here:

Fit, length Center front is 15″, the longest part from peak of the bust to lap is just under 16″.  Gentle sweetheart neckline, and slightly longline in the hips. This is a Level 3 silhouette, which is their curviest silhouette – so the bust is 8″ bigger than the waist, and the hips are about 10-11″ bigger than the waist.
Material 3 main layers – the outer fashion fabric (which may be brocade, satin etc as I have two different types in this review), flatlined to a sturdy cotton interlining, which is then treated as one layer, and also lined in twill.
Construction 6-panel pattern (12 panels total). Constructed with a slightly modified sandwich technique and double boned on the seams, just like the CS-411 and CS-426 style corsets.
Binding Binding at top and bottom are made from commercial black satin bias strips if the corset is made from a heavier brocade, OR made with matching colored satin if the overbust is finished in a satin fashion layer. Binding is machine stitched on both sides. There are also 6 garter tabs, 3 on each side.
Waist tape One-inch-wide waist tape running through the corset, hidden between the layers. I did not check to see if there was glue used in this one (see my CS-426 review if you want to know more about that particular corset).
Modesty panel There is a modesty panel on the back, made of a layer of black satin and a layer of twill if you have a brocade or tartan corset, but if you buy the blue satin CS-511, then it will be in matching blue satin. Panel is 5.5” wide (~4″ usable space) and attached to one side with a line of stitching. The old stock didn’t have a modesty placket by the busk, but the new stock does.
Busk Busk is 1/2″ wide on each side and 13” long, with 6 pins (the bottom two pins are slightly closer together, as is normal). It is fairly sturdy; less bendy than some other 1/2″ busks I’ve had.
Boning 22 bones total in this corset. On each side, 8 of them are spirals about 3/8 inch wide (double boned on the seams, except for between panels 5-6) and then there are two flat steel bones, both ¼” wide sandwiching the grommets.
Grommets There are 24 2-part size #00 grommets (12 on each side), with a small flange, spaced equidistantly. On the underside of the old stock corsets, every grommet is split and quite scratchy. On the new stock corsets, the grommets have rolled smoothly, they don’t tarnish and don’t catch on the laces.
Laces The laces are ¼” wide flat nylon shoe-lace style. I find them to be long enough and quite strong, but also rather springy. However, Orchard has some higher quality laces (in several colours) available on their website – I very much prefer their ribbon laces to the standard shoelace style laces.
Price Currently $79 USD on Orchard Corset’s website.

Final Thoughts:

It was an interesting venture to compare the old stock Orchard Corset pieces to the new stock. Of all the corset companies that I have dealt with, Orchard seems to be the most responsive to the requests of their clientele and eager to improve their designs, which is appreciated. The main changes to the corsets include the satin having matching modesty panels (not just black satin like in the brocade or Tartan pieces), better quality grommets that don’t tarnish or split as much, and the modesty placket by the knob side of the busk. I believe that their prices have dropped over time as well.

If I could choose only one colour or fabric of the CS-511, I would prefer the tartan more than satin – the sturdy and coarse weave of the tartan makes the corset look less wrinkly, and it’s also more resistant to abrasion and pulls, and feels more heavy weight and sturdy. The stripes in the tartan also match up fairly well – all this makes me a bit sad that this style is now on clearance (but that means that it’s only $59 at the moment, and I’m interested to see what new styles Orchard may bring in the future).

This corset also received 4 stars out of 4 on the Bust Test, as the bustline came up high enough on my chest to hold me in during activity. The pattern around the bust is very gently cupped (meaning it comes up and over the breast, not just pushes everything upward but it contains the bust) so I felt comfortable jumping, shrugging my shoulders, raising my arms and leaning over without feeling like I’m going to pop out.

Orchard Corset has graciously provided my viewers and readers with a non-expiring coupon code – enter CORSETLUCY to receive a 10% discount on your purchase. This corset and the other styles I’ve reviewed (including the CS-411 and the CS-426 underbusts) are available on the Orchard Corset website.