Pearls & Arsenic Red Swarovski Corset Review
This entry is a summary of the review video “REVIEW: Pearls & Arsenic Red Swarovski Corset” which you can watch on YouTube here:
|Fit, length||Center front is 11.25 inches long, princess seam is 9 inches (3.5″ above the waist, 5.5″ below the waist), side seam is 8 inches and center back is 12 inches.
Underbust 26″, waist 22″, low hip 33″.
Conical ribcage. Comes down low over the tummy, and sweeps up high on the back. This type of corset would fit someone with a high waist.
|Material||2 main layers; fashion layer is red satin, with many “garnet” (dark red) and “ruby” (light red) colored tiny Swarovski crystals. The strength fabric (lining) is black cotton coutil.|
|Construction||6 panel pattern (12 panels total). Panel 3 gives space over the hip, and panels 5-6 give plenty of space in the back. For construction: both layers were flatlined and treated as one. Panels were assembled and topstitched (seam allowances on the inside), and internal boning channels (cotton twill) were laid down to cover the seam allowance.|
|Waist tape||1.25″ wide waist tape, made from single-faced satin ribbon, exposed on the inside of the corset and secured down at boning channels. Partial width (from seam between panels 1-2 to seam between panels 5-6).|
|Binding||Bias tape made from matching red satin, neatly machine stitched on both inside and outside with a small topstitch (may have been stitched in one pass, using a special attachment). There are also 4 garter tabs (2 on each side).|
|Modesty panel||7.5 inches wide and finished in red satin fashion fabric / black cotton lining. Unstiffened, but quilted with many lines of stitching. Attached to one side of the corset with a line of stitching (easily removed if desired), and finished with binding on top and bottom. In the front there’s a slightly stiffened placket, 1 inch wide, finished in red satin, extending out from the knob side of the busk.|
|Busk||10″ long, with 5 loops and pins, equidistantly spaced. Slightly wider (3/4″ on each side) and slightly stiffer than a standard flexible busk.|
|Boning||14 steel bones not including busk. On each side, 5 spirals (1/4″ wide) are single boned on the seams, and 2 flats (1/4″ wide) sandwiching the grommets.|
|Grommets||24 grommets total (12 on each side), size #00 two-part grommets with small-to-moderate flange; set a bit closer together at the waistline, no wear/fraying/pulling out of grommets. I see no splits in the back, and the back panel is very good at not bowing or warping (see Final Thoughts).|
|Laces||Strong 1/4″ black nylon flat shoe-lace style laces; they have a bit of string, they hold bows and knots well, they glide well through the grommets, and they are long enough. (I would love to switch out the laces for some lush double-face satin ribbon to match the rest of the corset!)|
|Price||Although the corset in this review is a sample, Pearls & Arsenic corsets start at $193 USD.|
There are hundreds of small Swarovski crystals encrusting this corset, arranged in a gradient of deep “garnet” red crystals at the top and tapering down to lighter “ruby” red crystals towards the bottom. These were all hand-applied by Raven herself, and you can tell it was done with care – just the right amount of adhesive was used and each crystal was cleanly applied so there were no strings or residue oozing out from under the crystals. There was also care to keep the design symmetric on both sides, and to not have any crystals under the loops of the busk so it could be fastened properly. The crystals are also holding on securely and none of them are falling off.
On the center front and center back of this corset, there is a heavy-duty interfacing / canvas / buckram, or some other stiffener that helps keep the center front smooth (wrinkle-free) and flat, and prevents the back steels or grommets from warping or bowing along the horizontal plane. I seldom see corsets stabilized in this way and I found it interesting.
Do you own a corset by Pearls & Arsenic? Let us know what you think of it in a comment below!