Posted on 8 Comments

Corset Back TOO Straight? Curving Steel Bones for a Healthy, Neutral Posture

Last updated on January 6th, 2017 at 01:41 pm

Last week I wrote about what to do when your steels are too bendy or difficult to keep straight – so this week, we’ll discuss whether there’s anything you can do for steels that are too stiff (and of course you can! Otherwise I wouldn’t be writing about it). This will help you change the curvature of the back steels by the grommets

Since we’re talking about both human bones and corset bones in this post, I’m going to distinguish between them by saying “bones” for the human skeleton and “steels” for the corset bones.

Human vertebral column from the National Cancer Institute SEER training modules. This work is in the public domain.
Human vertebral column from the National Cancer Institute SEER training modules. This work is in the public domain.

Looking at the profile of the OTR corset in the video above, it’s pretty straight in the back which is potentially good for supporting the spine and promoting better posture than someone may have naturally. However, if you look at a vertebral column in the sagittal plane (from the side), you’ll notice that upright humans are designed to have some curve to the spine. There’s a small amount of lordosis of the neck, a mild natural kyphosis of the thoracic region, lordosis again in the lumbar area, and then (fused) kyphosis in the tailbone. While any exaggeration of these curves is not ideal, neither is having a spine that is perfectly straight.

Esther Gokhale did a fantastic TED talk on this concept of the “J shaped spine” and primal posture, which you can watch here.

If you have exaggerated lumbar lordosis (more swayback than the average person) you may find that when wearing a corset with a very stiff, straight back may feel like they’re encouraged to hunch forward at the waistline – and people who have a high “apple bottom” may find that the steels tend to dig into the top of the bum as opposed to curving around it. What can be done about this?

When your new corset comes in the mail, the steels are straight – they are typically not pre-bent in any manner.

Interestingly, corsets in the late Victorian era used to be pre-seasoned by steaming the starched corsets, whalebone included, on formed mannequins as the last step in manufacturing! So these corsets did have pre-curved whalebone. Today, pre-bending steels is something reserved for custom corsets by some corsetieres – and some other custom brands prefer to use flexible steels in the back which easily bends to accommodate the lumbar curve. To prevent twisting or bowing of these flexible bones, see the post I wrote last week.

If you have pronounced swayback and you can afford to go custom, I would recommend Electra Designs, and also Lovely Rats Corsetry – both of these corsetieres have a case of lumbar lordosis themselves and have learned how to draft to accommodate this curve (and adjust the pattern for the severity of the curve of each individual client) so the curve is built into the shape of the panels in the fabric itself, in addition to the curve of the steels.

But if you can’t afford to go custom, or if you already have an OTR corset where the steels in the back are too stiff for you, here’s an extremely detailed, step-by-step tutorial on how to curve the steels yourself.

How to curve the back steels to fit your neutral posture:

  1. Firstly, be sure that you are committed to keeping the corset. Curving the steels is manipulating the structure of the corset and this may void any returns or warranties.
  2. Try on the corset as is, look in the mirror, and figure out where you’re experiencing the most stress in your back and the most unnatural curve to your spine. In my corset, I noticed the most stress was below my natural waistline – which on me, is below the pull-loops of the corset and around the “inflection point” of my spine, where the kyphosis of my thorax turns into the lordosis of my lumbar region. Mark this line with fabric chalk (make sure your chalk doesn’t have any oil in it and can brush off easily). I know that I will have to curve everything below this point.
  3. Take off the corset and take the back panel of the corset in your hands, flanking the area where you need the most curve, and bend it gently to create a smooth rounded curve. Start with a small amount, of only a few degrees (enough that when you put the corset flat on a table, you can just barely see that the top and bottom edges of last panel doesn’t touch the table anymore).
  4. Try the corset on – see if it’s more comfortable or if you need a little more curve. If you think you could use more curve, remove the corset and gently coax the steels with your hands, only adding a couple more degrees at a time.
    DO start with less and add more curve until you’re happy.
    It’s less ideal to start with a huge amount of curve and then try to straighten it back. If you do end up being a little overzealous, you can use your hands to coax the steels straighter again, but be careful to curve them in the same area as before so your steel bone doesn’t become “ziggly”. Also try not to bend the steel back and forth too much as this weakens the steel.
    DO go by comfort and listen to your body.
    DO NOT go by what simply looks cute – remember, S-curve corsets were considered alluring because they accentuated the curve of the bum, but they ended up creating more back pain and strain because of the exaggerated curve.
  5. If you have weak hands and you do need more leverage:
    DO use a tailor’s ham like this one, or curve the steels over your knee.
    DO NOT fold the steels over completely backwards and create a kink in them. This is not origami.
    DO NOT brace the corset against the corner of a table to create more leverage to bend the steels.
    We are not geometrically shaped, and a jagged bend in the steel bone can create uncomfortable pressure points – not only this, but a sharp bend can also weaken the steel even if you try to bend it back the other way! You don’t want to increase the risk of the steel snapping over time –  so be gentle and only create a smooth rounded curve.
  6. If your problem area is only your tailbone, then only curve the very bottom of the steels upward like a ski jump. This will prevent the bones from digging into your bum.
    If your problem is more your upper lumbar area, then only curve this area instead. Again, try it on to test the comfort before making any other changes.

When I did this to my corsets, I noticed a few different benefits:

  • I no longer felt a strain in my lower back
  • Because my lumbar region felt more neutral, I stopped hunching forward with my shoulders and found that my chest opened up and I reduced tension in my upper back and neck
  • I could wear my corset for longer durations without feeling tired from my back trying to “fight” the corset to maintain proper posture
  • The upward flip of the bottom of the steels took pressure off of the top of my bum and personally helped improve my sciatica (a complication from my twisted pelvis from a childhood injury)

Remember that this is not a perfect science, so only go a tiny bit at a time, try it on for fit, see how it feels, then rinse and repeat until you hit a point where the corset feels most comfortable for you and your posture feels the most neutral. Most people have a natural lumbar lordotic curve between 40-60° (whereas a totally straight spine would be 0°), and some people will have a higher or lower bum, a more prominent or flatter bum, so not everyone will require the same amount of curve.

Other modifications you can make to a corset may include removing the back steels and replacing them with more flexible flat steel bones, or even spirals (however, this can be quite annoying and difficult to keep the back gap parallel), or you can add hip gores in the last or second-last panel to give the corset a bit more kick in the back and curve over your bum more comfortably.

How do you modify your corset for greater comfort? Leave a comment below!

Please note that this post is to modify the corset to help maintain your personal, natural posture for comfort purposes, and is not intended to be used to correct or modify any spinal deformities, whether congenital or acquired, for therapeutic purposes. If you feel that a corset can help improve your skeletal structure and/or health, please consult your trusted healthcare practitioner.

8 thoughts on “Corset Back TOO Straight? Curving Steel Bones for a Healthy, Neutral Posture

  1. I just found this article today and have already started adjusting my back busk, and OMG!!!! What a huge difference this has made. It’s no longer digging into my behind and I am not rolling my shoulders forward as much. I think a bit more tweaking over the next couple days and I will have it just right. Thanks so much for your helpful advice.

  2. I’ve been bending my back steels but could not get this right for two years until today. After a careful look in the mirror, I finally noticed my back starts curving -above- the waist tape on my corset, in my neutral standing position. I re-bent my steels accordingly and oh my goodness, all the pressure points on my sacrum finally disappeared. This was magical!

    I kept thinking my spinal inflection started at or below the waist tape because that’s where my pressure was, but not the case.

    1. That’s great to hear Edie! Glad it worked for you after a small tweak!

  3. This was very helpful, I got my corset 3 years ago and never went back to corseting after experiencing weird shoulder pains. Recently I just went back after being hopeful again to trim my waist line, the stretchy workout wrap corsets did help me with my weight loss so I thought why not trying the hardcore steel corset sitting at my drawer for years again. I came across your chanel and saw these instructions, it gave me an idea that this might be the reason why my off the rack corset was giving me pains. Gave it a try and slightly curved my upper busks that I never noticed was indeed “digging” my upper back. Now I can sit to it for long hours. No more pain and now enjoyable. Thank you so much Lucy. I am now being able to start this long journey :)

    1. I’m so happy this worked for you, Karen! Thank you for your positive feedback. :)

  4. I was young when I started wearing a corset for bone structuring. It worked for me. Thanks for sharing this.

  5. Can you do this with the front busk as well? I have a mild pectus excavatum which causes pressure on my front lower ribs and having a bit of curve to the front might be good!

    1. Hi Cassandra, yes you can gently curve a standard width busk (the half-inch wide busk on each side). :) Just be careful not to pop off any of the knobs!

Comments are closed.