Posted on 7 Comments

Madame Sher Mesh underbust corset Review

This post is a summary of the Madame Sher black mesh cincher Review, which you can watch on Youtube if you prefer:

Fit, length Front is about 11 inches long, from the shortest part (close to the side seam) is 8.5 inches long. The top and bottom edges in front and back are slightly pointed, as many ribbon cincher styles seem to be. I consider this a “modern” hourglass shape (cupped ribs and cupped hips) although some may consider it a wasp waist silhouette. I submitted my measurements to Madame Sher, so this corset was custom made for my figure.
Material 1 main layer: it’s mostly a black soft mesh, which feels like cotton (it feels similar to cross-stich canvas). It has a small amount of stretch, but still strong. Vertical panels (in front, side and back) is black cotton twill.
Construction 13 literal panels, but technically you can consider it a 5 panel pattern. The horizontal “ribbon” panels are assembled with a flat-felled seam, then are sandwiched between the twill vertical panels (which are also double-stitched).
Binding Black binding made from bias strips of matching black twill. Machine stitched on outside and inside (Madame Sher mentions that it’s stronger this way).
Waist tape Most ribbon cinchers don’t incorporate a waist tape usually, but the center “ribbon” panels closest to the waist are also lined in black twill, which helps reinforce this area. Although it might stretch a little bit, the corset itself still gives me a great silhouette.
Modesty panel Interesting modesty panel – fully boned (the bones going vertically) and covered in black twill. My corset came with 2 panels (one was 6″ wide, one was 8″ wide) and they are removable/ interchangeable using small ribbons and grommets. Also, this has an unstiffened modesty placket under the busk.
Busk Sturdy special busk, about 3/4″ wide about 10.5″ long (5 pins). The busk is cut on an angle, and te binding is sewn only a couple of millimeters away from the end of the busk! Madame Sher commissions a local jeweller to make her busks, which are easily recognisable from the square loops!
Boning 8 total bones not including busk. On each side there are two 1/2″ wide heavy spiral steel bones. On the back by the grommets there are two pairs  On each side they are double boned on the seams (1/4″ wide), 2 sturdier flat-steel bones sandwiching the grommets which are closer to 1/4″ wide.
Grommets 24 grommets total, size #00 two-part grommets with small flange; set equidistantly, no wear/fraying/pulling out of grommets, but many splits. However they don’t seem to catch on the laces much.
Laces Very thin (less than 1/8″ wide) nylon rat-tail laces, very strong, glides through the grommets quite well.
Price At the time that I’m writing, it is $220 USD on Madame Sher’s website in the Tight Comfort section.

Final Thoughts:

I adore this corset. It is one of my least expensive custom fit corsets that I own, yet it is one of the most comfortable. When I’m having a “lazy” or comfortable day, or if it feels too hot to wear a full cotton corset, then I’ll wear this mesh piece. It feels breezy and looks wonderful under dresses as well.

There is only one small thing to note about wearing this corset under clothing – because the cincher has horizontal “ribbon” panels, then the lines or bulges under a dress is not vertical (as would be usual, due to boning channels, mostly) but rather in this case the cincher creates horizontal bulges. Depending on who you are and what your BMI is, you may find that it looks a little bit like a ribcage under your dress. However, I do find that this corset is MUCH less conspicuous under clothing compared to some other corsets! Another perk is that this corset is so soft and lightweight that it’s one of the few that I feel comfortable directly next to my skin, if I want to wear stealth on hot days. Because it came with two modesty panels that can be quickly and easily switched out, it means I can have one in the wash and one to wear.

I was intrigues with Madame Sher’s corsets because of her unique construction and materials: I have never had a soft summer mesh corset like this before (I had owned the Contour Corsets summer mesh corset, but that one is very heavy duty!), and also have relatively little experience with ribbon cinchers. The modesty panel’s full horizontal boning and attachment are also unique, as is the special square busk, and even the rat-tail lacing! This is a beautiful example of ingenuity, and it goes to show that not all corsets have to be created the same way.

If I were to go back and order another mesh corset from Madame Sher, I would likely spend the $50 more to try out the full mesh underbust (both to try something different, and also because I think it would be more sturdy due to more boning and satin waist tape). I have no complaints about the cincher, but I think I might prefer the full underbust in the future. Although this corset is so unique that I cannot really compare it to anything else, I would say it’s excellent for the value.

You can find the summer mesh cincher and other styles on Madame Sher’s website here.

Posted on 12 Comments

Introducing the new Corset “Paper Doll” Designer!

One of my own corset creations, "cartoonized" in the paper doll corset designer.
One of my own corset creations, “cartoonized” in the paper doll corset designer.

This is the project I’ve been waiting so long to tell you about (well, one of them).
It started around springtime of 2012, when I was talking with another corsetiere about effective communication between maker and client. A bespoke corsetiere is supposed to take the client’s vision and bring it to life – but sometimes, due to language barriers or other circumstances, miscommunication can happen and the end product doesn’t match the client’s vision.

My wish was to create a virtual “paper doll” game (that are so popular today on little princess websites) that applies specifically to corsetry. Length, shape of the edges, colour, fabric, boning channel options and closures would all be adjustable.
More importantly, anyone can use this – whether you’re a client or a corsetiere – to help you communicate more effectively.

It took a long time and quite a bit of money to get the project to this point – it was only August of 2012 before I actually found a program developer (J Artis) who would take on this project, and finally in November I found the perfect graphic artist (Christine) to create the doll itself. It’s been a long road, and I’m certain we will be ironing out some wrinkles (and with any luck, adding a couple more features) over time.

There are opportunities for collaboration regarding this project e.g. corsetieres can submit unique fabric swatches from their stock (which will be credited) and sponsor the project which will help keep this app going and help keep it free. The “red tiger stripe” print option is a placeholder that shows you the concept behind a print/brocade fabric underlay.

One note: although the button that says “Request a Quote” is functional, I’m not currently accepting bespoke commissions. If you intend to send this form to another corsetiere for a different commission, I would be 100% happy to forward the form to you for reference, and/or keep your selections and measurements for reference when I resume consultations.

Without further ado, I present to you the Designer. Go play!